manualshive.com logo in svg

GE CyberDome Series, Installation Manual, Page: 34 / 52

Share
Download
GE CyberDome Series Installation Manual Download Page 34

PTZ and Dome Installation

CyberDome Series Installation Manual

34

A06-8SG0/B/April2006/1033921C

Figure 52:  Attaching the Dome Assembly to the Upper Housing

Installing the Dome Assembly

The CyberDome comes with one of four acrylic dome assembly options: clear, tinted, smoked,
chrome mirrored and gold mirrored domes. Each dome assembly attaches to the upper
housing with interlocking clips and a dome safety cable.

CAUTION!

DO NOT touch the acrylic when handling the dome assembly. Use a scratch-resistant cloth.

To attach the dome assembly to flush- and pendant-mount housings:

Step 1)

Fasten the dome safety cable to the upper housing with the safety clip. See

Figure 52

.

Step 2)

Position the dome such that the angled ends of its mounting clips face the angled
ends of the clips attached to the upper housing.

Step 3)

Turn the acrylic dome clockwise, so that the ends of the mounting clips engage
and lock into place.

Summary of Contents for CyberDome Series





















































Reviews:

No comments