manualshive.com logo in svg

GE CyberDome Series, Installation Manual, Page: 23 / 52

Share
Download
GE CyberDome Series Installation Manual Download Page 23

CyberDome Series Installation Manual

Housing Installation

23

A06-8SG0/B/April2006/1033921C

Figure 35. Cable Assembly Connections in the Junction Box

Step 10)

WITH POWER OFF, make the facilities connections to the terminal strip on the
inside of the junction box cover. See 

Figure 35

.

Step 11)

Install the junction box cover. Ensure that the sealing gasket is properly posi-
tioned.

Step 9)

Place the sealing gasket on the inside of the junction box cover, and then make
the cable assembly connections to the terminal strip. See 

Figure 35

.

Step 7)

Feed the end of the cable assembly coming out of the mounting socket through
the nipple on the top of the junction box. See 

Figure 33

.

Feed the video cable BNC connector through the nipple first, and then the twisted-
pair bundle.

Step 8)

Remount the junction box onto the mounting plate using the hardware provided.
See 

Figure 34

.

Figure 33. Cable Assembly into the Chase Nipple

Figure 34. Remounting the Junction Box

Summary of Contents for CyberDome Series





















































Reviews:

No comments