manualshive.com logo in svg

GDS Compuprint 2056, User Manual, Page: 59 / 68

Share
Download
GDS Compuprint 2056 User Manual Download Page 59

User Manual                                                                                                                                      2056 

MAN10xxx-01 51 

 

Item Description 

Compress 
printing 

Support graph and character compress printing. 

Special 
function 

Pin Break Compensation; Pin Rotation Replacement; Automatic 
Emulation Match; Online Aptitude Parameter Setting. 

Physical 
dimensions 

384 (width) × 280 (depth) × 139 (height) mm 

Weight 

Approx. 6 Kg 

Environmental 
conditions 

Operating 
environment 

Temperature: 5 ~ 35

℃

 

Humidity: 25 ~ 80%RH (No condensation) 

Storage environment 

Temperature: -40 ~ 55

℃

 

Humidity: 

≤

93%RH (40

℃

, No condensation) 

Power 
requirements 

Rated voltage: 220 V(AC) 
Rated frequency: 50Hz ~ 60Hz 

Power 
consumption 

Operating: 70 W;   Standby: Approximately 4.6 W 

 
 

 

Certificate 

CE Certificate 
CCC Certificate 

 
 
 
 
 
 
 
 
 
 

Note: All the technical instructions in this user's manual are the laboratorial

measurements which achieved under national standard store and work 
environment (room temperature), the measuring paper accords with the 
specification in this user's manual.

 

Note: Only when the product is unconnected with outer power 

supply, it can achieve zero energy consumption state.

 

Summary of Contents for Compuprint 2056





































































Reviews:

No comments