GDS Compuprint 2056 Page 16 User Manual Download | Manualshive

Page: 16 / 68

background image

User Manual 2056

MAN10xxx-01 8

1.8.2 Connecting to the USB Interface

1. Plug the USB cable A end (flat shape) into the computer's USB interface.
2. Plug the USB cable B end (square shape) into the printer's USB interface (As shown in

figure 1-14).

1.8.3 Connecting to the Serial Interface

1. Turn off both the computer and the printer. Plug the serial interface cable into the printer’s

serial interface. Tighten the screws on both sides of the connector and make the connector

fixed. (As shown in figure 1-15)

2. Plug the other end of the cable into the computer’s serial interface, make sure it connects

tightly.

1.8.4 Connecting to the Ethernet Interface

1. Plug the RJ-45 crystal end of the Ethernet interface cable into the printer Ethernet

interface, and plug the other end into the LAN. (Shown as figure 1-16)

Figure 1-15 Connect to serial interface

Figure 1-14 Connect to USB cable

USB interface

USB cable

USB interface

Serial interface

Serial interface cable

Screw

Note: Don't impact the plug after connecting to the USB cable.

«
...
14
15
16
17
18
...
»

Summary of Contents for Compuprint 2056





































































Reviews:

No comments

Related manuals for Compuprint 2056

IMAGERUNNER ADVANCE C5051

Brand: Canon Pages: 72

iPF710 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 92

iPF8000S - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

imageRUNNER ADVANCE C9075S PRO

Brand: Canon Pages: 48

Two-Knife Booklet Trimmer-A1

Brand: Canon Pages: 32

Perfect Binder-C1

Brand: Oce Pages: 82

IMAGERUNNER 7095 PRINTER

Brand: Canon Pages: 615

imageRUNNER C3125i

Brand: Canon Pages: 816

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

CLP-770ND - Color Laser Printer

Brand: Samsung Pages: 2

CLP 610ND - Color Laser Printer

Brand: Samsung Pages: 114

Brand: Samsung Pages: 6

Brand: Samsung Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands