GDS Compuprint 2056 Page 35 User Manual Download | Manualshive

Page: 35 / 68

background image

User Manual 2056

MAN10xxx-01 27

Chapter 3 How to Use the Printer

Here are the steps of using printer:

1. Install the printer as the description in chapter 1, connect the printer to your computer and

install the driver correctly.

2. Load the correct type of paper.
3. Set the printer if necessary.
4. Send the print command to the printer to print.

3.1 Loading the Paper

In addition to printing on cut sheet and tractor papers, your printer can also print on a wide

variety of paper types, including multi-ply paper, labels and envelopes.

Please make sure the printing contents are all within the printable area while printing. The

correlative printable area, see the Appendix A for reference.

3.1.1 Loading Cut Sheet

1. Make sure the printer is powered off, and open the window of the printer, refers to chapter

Gap Adjust Lever of this manual, pull the gad adjust lever to cut sheet position according

to the paper type.

Figure 3-1 Adjust the gap adjust lever

Caution: When printing on multi-ply paper, the print force is stronger as the

paper is thicker than other common paper. Please make sure the
printing are entirely within the printable area or it can damage the print
head.

«
...
33
34
35
36
37
...
»

Summary of Contents for Compuprint 2056





































































Reviews:

No comments

Related manuals for Compuprint 2056

All in One Printer

Brand: Xerox Pages: 3

Brand: DataCard Pages: 2

Brand: Datamax Pages: 2

Brand: BIXOLON Pages: 29

Brand: Konica Minolta Pages: 266

Brand: Make Mendel Pages: 29

Brand: Citizen Pages: 32

Brand: oti Pages: 33

Brand: Jolimark Pages: 65

Brand: Oce Pages: 66

Brand: DNP Pages: 33

Brand: 3D Systems Pages: 29

Brand: Canon Pages: 48

Pixma PRO-100S series

Brand: Canon Pages: 4

Pixma PRO-100S series

Brand: Canon Pages: 2

Brand: Canon Pages: 570

Brand: Canon Pages: 571

Brand: Canon Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands