GDS Compuprint 2056 Page 5 User Manual Download | Manualshive

Page: 5 / 68

background image

User Manual Compuprint 2056

MAN10xxx-01 iii

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when the operating instructions are followed.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance, it indicates a need for service.

Warnings, Cautions and Notes

Pay attention to the following promises when using this manual:

Warnings:

Warnings must be followed carefully to avoid bodily injury.

Cautions:

Cautions must be observed to avoid damage to your equipment.

Notes:

Notes contain important information and useful tips on the operation of your printer.

Note: The contents of this manual are subject to change without notice.

* All parts of the printer can be recycled. When it is abandoned, we can call it

back freely. Please contact us when you abandon it.

«
...
3
4
5
6
7
...
»

Summary of Contents for Compuprint 2056





































































Reviews:

No comments

Related manuals for Compuprint 2056

Brand: Canon Pages: 86

Brand: Canon Pages: 20

Sure shot 80 tele

Brand: Canon Pages: 24

iPF720 - imagePROGRAF Color Inkjet Printer

Brand: Canon Pages: 8

Brand: Canon Pages: 2

Brand: Xerox Pages: 25

Brand: 3Doodler Pages: 8

Brand: µ-Dimension Pages: 74

Saddle Finisher-AF2

Brand: Canon Pages: 244

Brand: BCS Pages: 151

WorkCentre 7655

Brand: Xerox Pages: 24

Brand: GCC Technologies Pages: 97

4250 - WorkCentre - Copier

Brand: Xerox Pages: 4

Brand: CNET Pages: 2

Brand: Oce Pages: 66

Brand: Aficio Pages: 92

Accel-a-Writer 4

Brand: Xante Pages: 12

Brand: Xante Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands