background image

1

GAUI 

TAI SHIH HOBBY CORPORATION

Thank you for purchasing 

GAUI

         High Performance RC Helicopter from 

Tai Shih Hobby Corporation (TSH). We hope you will enjoy the joy of flight.

感謝您購買泰世科技出品的 

GAUI

     高性能遙控直升機,我們希望您可以盡情

享受飛行的樂趣。

In order to understand full assembly sequences, this instruction manual show the 

assembly information of this model, even though some elements are 

supplied as pre-assembled. Please refer to it when carrying out maintenance or 

replacing parts.

為了要讓使用者詳細瞭解組裝順序,即使有些部件已經預先組裝完成,
本說明書將提供這台遙控模型的組裝資訊。同時,敬請參閱保養與主要零件更換資
訊。

CAUTION: This radio controlled helicopter is not a toy.

                 The product is not suitable for

                 children under 14 years of age.

注意:此無線電遙控直升機不是玩具,該產品是不適合14歲以下的兒童。

SAFETY PRECAUTIONS

 This kit includes some preassembled components. Please check for any 

 loose screws and tighten them before you proceed with assembly.

 You are responsible for assembly, safe operation, maintenance, inspection and 

 adjustment of the model.

 Before beginning assembly, please read these instructions thoroughly.

 Check all parts. If you find any defective or missing parts, contact your local 

 dealer or 

GAUI

 TSH distributor.

 Before you proceed to RC helicopter activity, please check and follow thoroughly 

 related regulation of aero modeling in your country/region.

安全資訊與注意事項
 這台遙控模型包含預先組合完成的部件。
 在進行組裝之前,請仔細檢查這些預先組裝部件上的所有螺絲均有仔細鎖緊。
 您有完全的責任對於這台遙控模型的組裝,安全操作,保養,檢查與調整。
 請先檢查所有的零件,如果發現任何不良品,遺失品,請向模型店或是當地的
 泰世代理商連絡。
 在您進行遙控直升機活動時,請先詳細瞭解與遵守當地遙控模型的相關法規。

前言

Preface

Summary of Contents for X7 Flybarless







































Reviews: