EN
EN
124
125
IMPORTANT -
Proteins curdle in hot water and, therefore, stick to the surfaces even
more stubbornly. Thus, after processing eggs or other protein-rich ingredients, you
should rinse the parts with cold water first.
8. Soak stubborn or dried-on residues of food for approx. 10 minutes in lukewarm
dishwater.
9. Clean the used accessories and, if required, all mincing discs in warm dishwa-
ter, using a soft cloth or soft brush. You may clean the holes in the mincing discs
via a clean pipe cleaner.
10. Stubborn residues in the interior of the mincer housing and/or sausage horn may
be removed via a soft bottle brush.
11. Dry all parts thoroughly after cleaning and leave the parts dry naturally for
approx. 1/2 hour, where they are
out of reach of young children
.
12. After cleaning and drying the mincing discs, rub the mincing discs with some
cooking oil.
IMPORTANT -
Always protect the mincing discs from moist and humid air (see:
‘Storage’), when they are not in use.
CLEANING IN THE AUTOMATIC DISHWASHER
CAUTION
– The plastic parts (multi-purpose container, pasta discs, adapter for
sausage, kebab and cookies) may get distorted when exposed to high temperature.
Some metal parts (mincer housing, worm shaft, mincing discs, scraper beater, knea-
ding tools) corrode when coming in contact with the corrosive cleaning agents used
in dishwashers. Please, follow the instructions for cleaning, given below, before pla-
cing any parts and accessories of the stand mixer in an automatic dishwasher.
IMPORTANT -
In an automatic dishwasher, you may clean only those parts men-
tioned below. All other parts may only be cleaned manually in warm dishwater
according to the instructions given above. For cleaning in an automatic dish-
washer, always use a low-temperature program and place the plastic parts in the
upper rack.
Only the following parts are
suited for cleaning in an automatic dishwasher:
Mixing
System: Mixing bowl, splash guard, wire whisk.
Mincer:
pusher and tablet.
STORAGE
WARNING
– When the machine is not in use, always switch OFF the motor
(press the control dial) and unplug the machine to avoid hazards due to moving parts,
overheating, fire, and electric shock. Do not hold the machine at the mixing arm,
mixing bowl, mixing tools, installed mincer, or power cord for moving the machine.
CAUTION
– Always grasp the machine at the front and back of the base
plate for moving it. Keep in mind that the machine is very heavy. Additionally,
the
machine is fixed to the work surface with 6 suction cups, making it difficulty to
lift the machine
. The mixing arm must be locked in the operating position for
moving the machine and/or when the machine is not in use.
IMPORTANT -
Ensure to store the machine where it is clean, dry and safe from
frost, direct sunlight and inadmissible strain (electric or mechanical shock, fall
down/over) and where it is
out of reach of young children and animals
. Do not
place any hard or heavy foreign objects on or in the machine or any part of it.
It is good advice to install the mixing bowl and splash guard for storage. Additional-
ly, you may place the mixing tools and the
plastic parts
of the mincer into the mixing
bowl for protecting the mixing tools from loss and damage. However,
ensure that
the parts in the mixing bowl will not get damaged when lowering the mixing
arm to the operating position
.
1. Before storage, clean the machine and all used accessories (see: ‘Care and
Cleaning’). Ensure to rub the steel mincing discs with some cooking oil.
2. Lock the mixing bowl at its place on the base plate (see: ‘Preparation’). Place the
mixing tools and the
plastic parts
of the mincer
carefully
into the mixing bowl.
3. If required,
carefully
lower the mixing arm to its operating position,
ensuring
that the mixing arm will not damage any of the tools and accessories
. Cover
the mixing bowl via the splash guard.
4. Assemble the mincer with worm shaft, cross blade, a mincing disc and the screw
ring (see: ‘Using the Mincer / Processing Tough Food—Mincing Meat’). This
will protect the cross blade best from unintended touch.
5. If required, you may push the power cord into the cord storage. Alternatively, lay
the power cord carefully into the gap between the mixing bowl and the back
pillar of the machine.
