EN
EN
96
97
NOTE
You can change the speed at any time you like during operation. The set operating
time cannot be changed, while a mixing process is running. If required, cancel the
current mixing process (see: ‘Operating Time and Pause Function’).
NOTE
If you wish to add further ingredients, you should interrupt operation for this. Use
the pause function, if you wish to resume operation thereafter (see: ‘Operating
Time and Pause Function’).
5. For changing the speed during operation, turn the control dial to the desired
value. If required, you may interrupt the mixing process at any time you like by
simply pressing the control dial
shortly
. The motor stops immediately. The cur-
rent speed setting is kept and the count-down of the operating time stops at the
current setting (see: ‘Operating Time and Pause Function’). Use this function for
adding further ingredients.
6. If required, you can cancel operation manually at any time you like (see: ‘Opera-
ting Time and Pause Function’). In this case, the settings for speed and operating
time will be reset to the defaults (speed zero and 20 minutes). If you leave the
machine operate until the set operating time elapses, the machine stops automa-
tically. Thereafter, the default operating time is shown again on the operating
time display (20 minutes, “20:00”). You may start operation again at once.
IMPORTANT -
When processing very heavy dough or leaving the machine ope-
rate for several minutes, the mixing arm gets somewhat warm. This is normal and
no need for concern. However, do not leave the motor run in continuous operation
for more than 10 minutes.
7. If you do not wish to use the machine again, switch off the machine complete-
ly by pressing the control dial until only dashes are shown (see: ‘After Usage’).
Then unplug the machine. Do not leave the machine connected to the power
supply uselessly.
8. Do not leave any food dry on the surfaces. Clean the machine and any used
tools immediately after operation. This will keep the machine hygienically clean
and always ready for use (see: ‘Care and Cleaning’).
USING THE MINCER
WARNING
– Do not hold your hands or any foreign objects in the feed chu-
te of the mincer or at the mixing drive, when the machine is connected to the
power supply. Even for operating the mincer, install the mixing bowl at the base
plate of the machine and cover the mixing bowl via the splash guard to protect
the mixing drive against unintended touch. Do not hold your face over the feed
chute, while the motor is agitating, because splinters and splashes could be hurled
out of the feed chute, especially, when you failed to remove small pieces of bones
or other hard parts (e.g. stalks, hard seeds, stones) while preparing the food. Only
use the provided pusher for pushing down the food in the feed chute.
WARNING
–
Do not remove the screw ring from the mincer housing, whi-
le the mincer is mounted on the mixing arm
and the machine is connected to the
power supply. Always switch off the motor (press the control dial) and unplug the
machine, when the motor gets stuck or runs noticeably slowly. Always remove the
mincer from the mixing arm for removing obstacles (see: ‘Removing Obstacles’).
DO NOT pour water or any other liquids into the feed chute of the mincer, while the
mincer is assembled to the mixing arm. Do not process very wet or runny ingredients
via the mincer (e.g. light batter, fresh fruit or vegetables) to avoid risk of electric shock.
CAUTION
– Do not process frozen or too hard food (e.g. nuts, coconut, dried
spices) to avoid damage. Always remove extremely hard parts of your food (e.g.
bones, hard shells, seeds). The mincer is suited for processing fresh meat and food of
similar consistency as well as heavy types of dough (e.g. pasta dough). Always select
the appropriate set of tools for processing your food (see below). Before switching on
the motor, always ensure that the mincer is assembled completely and correctly.
IMPORTANT -
Do not operate the mincer in combination with the mixing drive to
avoid overloading the motor. When the motor is running for several minutes, the
mixing arm may get warm. This is normal. However, do not let the motor run con-
tinuously for more than 10 minutes to avoid overheating. Make a break of at least
5 minutes after each 10 minutes of operation.
NOTE
You may operate the mincer without setting the operating time and use the default
of 20 minutes (“20:00”). We recommend to set the operating time to 10 minutes
for being reminded to make brakes in time. This will help to maintain the high
performance and long lifetime of the motor. Use the breaks for preparing the next
portion of food, or for performing the next step of making your dishes with the food
already processed via the mincer.
