GasTech F-GUARD IR3-HD User Manual Download Page 3

Page: 3 / 45

For more information & technical support: [email protected]· [email protected]

iii

76-M-6010-02-02

F-Guard IR3 HD User Manual

Table of Contents

Introduction .................................................................................................................... 1

Key Features ........................................................................................................................1

Model Number Description ..................................................................................................2

Internal tests .......................................................................................................................2

Product Overview ................................................................................................................3

Accessories ..........................................................................................................................4

Installation ..................................................................................................................... 7

General Considerations ........................................................................................................7

Preparations for Installation ............................................................................................... 10

Required Tools ................................................................................................................... 10

Certification Instructions .................................................................................................... 10

Mounting the Tilt Mount .................................................................................................... 11

Mounting the detector ....................................................................................................... 12

Electrical Wiring ................................................................................................................. 13

Current Output (0-20mA) Wiring ........................................................................................ 16

4 Wire Relay Connection .................................................................................................... 17

RS-485 Communication Network ........................................................................................ 18

Cabling Recommendations ................................................................................................. 18

Earth/Ground Regime ........................................................................................................ 18

Configuration options ................................................................................................... 20

Sensitivity .......................................................................................................................... 21

Ultra-Fast Detection ........................................................................................................... 21

Alarm Delay ....................................................................................................................... 21

Alarm Latch ....................................................................................................................... 21

Enable Pre-Alarm 0-20mA .................................................................................................. 21

Enable dirty window warning 0-20mA ................................................................................ 21

Auxiliary Relay ................................................................................................................... 22

Window Heater ................................................................................................................. 22

Summary of Contents for F-GUARD IR3-HD














































Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Related manuals for F-GUARD IR3-HD

Brands by name

Popular brands

GasTech F-GUARD IR3-HD, User Manual

Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Related manuals for F-GUARD IR3-HD

Brands by name

Popular brands