GasTech F-GUARD IR3-HD User Manual Download Page 44

Page: 44 / 45

For more information & technical support: [email protected]

76-M-6010-02-02

F-Guard IR3 HD User Manual

Appendix A

HART 7 Communications

Highway Addressable Remote Transducer (HART®) establishes digital data communication

over 4-20mA Current Loop cables. The HART protocol uses FSK modulation signals

superimpose at a low level on top of the 4-20mA current.

The HART implementation on the F-Guard IR3/UV-IR Flame Detector allows the Control Unit to

monitor the status of the detector, settings of User Configuration and initiate field diagnostics.

The HART protocol implemented in this flame detector corresponds to HART rev. 7.0.

It supports HART Universal commands including Common Practice and Device Specific

Commands.

Gastech
24 Baretta Rd, Wangara, 6065
Tel: +61 8 6108 0000
Email: [email protected]

Summary of Contents for F-GUARD IR3-HD














































Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Brands by name

Popular brands

GasTech F-GUARD IR3-HD, User Manual

Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Brands by name

Popular brands