GasTech F-GUARD IR3-HD User Manual Download Page 10

Page: 10 / 45

For more information & technical support: [email protected]

76-M-6010-02-02

F-Guard IR3 HD User Manual

1.5.3 Pole mount

The pole mount enables the detectors to be

installed with its tilt mount brackets. The pole

mount kit we supply is suitable for 2-inch or 3-

inch poles. Part number

F-Guard

-PMA-S23.

IGURE

OLE

OUNT

1.5.4 Air shield

The air shield P/N

F-Guard

-ASD-S02 allows

the installation of flame detectors in harsh

weather conditions where they may be

exposed to dust, sand, and other particulate

matter. The connection point can be mounted

in the 3, 9 or 12 o’clock locations.

•

Air pressure source: Clean, dry, and oil-free

air

•

Pressure: 2-3 bar /30-45 psi

•

Fitting: 7/16”—20UNF-2A

•

Operation temperature: -55°C to +85°C / -

67°F to +185°F

IGURE

HIELD

Summary of Contents for F-GUARD IR3-HD














































Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Related manuals for F-GUARD IR3-HD

Brands by name

Popular brands

GasTech F-GUARD IR3-HD, User Manual

Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Related manuals for F-GUARD IR3-HD

Brands by name

Popular brands