GasTech F-GUARD IR3-HD User Manual Download Page 25

Page: 25 / 45

For more information & technical support: [email protected]

76-M-6010-02-02

F-Guard IR3 HD User Manual

3 Configuration options

Some functions of the detector can be configured using an RS-485 modem connected to

a computer with the “

Gastech

communicator” software. For details of how to download

the software please contact technical support via email at [email protected]

These configuration options are listed in the following table along with their factory

default values.

ABLE

ETECTOR

ONFIGURATION

PTIONS

Function

Options

Default Setting

Sensitivity

Very low, Low, Medium, High,

Extreme

Medium

Ultra-fast detection

Disabled, Enabled

Disabled

Alarm Delay

0, 5, 10, 20 or 30 seconds

0 seconds (no

delay)

Alarm Latch

Disabled, Enabled

Disabled

Video module

Disabled, Enabled

Enabled

Video analog output

Disabled, NTSC, PAL

Disabled

Enable Pre-Alarm 0-20mA

Disabled, Enabled

Disabled

Enable dirty window warning 0-

20mA

Disabled, Enabled

Disabled

Aux. Relay

Alarm
Pre-Alarm
Dirty Window Warning

Alarm

Window Heater

Disabled, Enabled

Enabled

Modbus address

1 – 247

Manual BIT – Alarm Output Test Disabled, Enabled

Disabled

•

Note:

Medium sensitivity setting allows detection of a 1x1ft

(0.1m

) N-

heptane pan fire at a distance of 100ft (30m).

Summary of Contents for F-GUARD IR3-HD














































Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Related manuals for F-GUARD IR3-HD

Brands by name

Popular brands

GasTech F-GUARD IR3-HD, User Manual

Search results

Summary of Contents for F-GUARD IR3-HD

Reviews:

Related manuals for F-GUARD IR3-HD

Brands by name

Popular brands