USE AND MAINTENANCE
ENGLISH
-
(1
cod. G19504810
3
4
1
2
5
¿J
4.9.8 LOBE COMPRESSOR
)LJ
7KHURWDU\OREHFRPSUHVVRUJHQHUDWHVFRPSUHVVHGDLUZKLFK
IHHGVWKHHMHFWRUWRWUDQVSRUWWKHVHHGIURPWKHGURSSRLQWIURP
WKHGLVFWRWKHVHHGLQJIXUURZ
7KHOREHFRPSUHVVRULVGULYHQE\DK\GUDXOLFPRWRUFRQQHFWHG
WRWKHWUDFWRUGLVWULEXWRUZLWKFRQWLQXRXVRLOGHOLYHU\DQGWRDIUHH
GUDLQSUHVVXUHIUHHPD[EDU
NOTE
LWLVDGYLVDEOHWRXVHDWUDFWRUZLWKDYDULDEOHÀRZK\GUDXOLF
pump and electro-hydraulic distributors that can be adjusted from
the tractor.
:LWKWKHHQJLQHR௺DQGWKHWUDFWRULPPRELOL]HGFRQQHFWFRUUHFWO\
all the quick-couplings. Start the engine and operate the system
at idle for a few minutes bringing constant pressure to the entire
circuit. It is possible to regulate the pressure only when the oil has
reached the right temperature.
IMPORTANT!
-
Avoid rotation in the inverse direction when the compressor
is stopped as it can damage the motor.
- Check the rotation speed using the inductive sensor on the
front box.
7KHSUHVVXUHRIWKHDLUJHQHUDWHGE\WKHFRPSUHVVRULVFDOLEUDWHG
E\WKHWUDFWRUJUDGXDOO\DGMXVWLQJWKHRLOÀRZRIWKHGLVWULEXWRU
7KH
Virtual Terminal
LQGLFDWHVWKHYDOXHVRIWKHURWDWLRQVSHHGRI
WKHOREHFRPSUHVVRUDQGWKHGHOLYHU\DLUSUHVVXUH
%HORZLVDWDEOHZLWKLQGLFDWLYHYDOXHVRIDLUSUHVVXUHEDVHGRQWKH
W\SHRIVHHGWREHGLVWULEXWHG
Seeds type
No. of compressor
revs (rpm) - CT50
Air Pressure
(bar)
&RUQ
·
a
6XQÀRZHU
·
a
6R\D
·
a
6XJDUEHHW
·
a
6RUJKXP
·
a
Rape
·
a
The indicated values are valid for an 8-row in seeding.
IMPORTANT!
- If the equipment is used with more than one tractor and, con-
VHTXHQWO\GL௺HUHQWGLVWULEXWRUVDQGRLOVLWZLOOEHQHFHVVDU\WR
repeat the calibration procedure for each tractor.
-
The lobe compressor is fundamental for successful preci-
sion seeding and therefore, must always be actuated during
work.
- Periodically check the operating pressure and the shaft
rotation speed (maximum threshold 4500 rpm) which can
EHGLVSOD\HGLQWKH9LUWXDO7HUPLQDORQWKHVSHFL¿FSDJHV
- If the maximum speed is exceeded, the system must be
stopped.
Risk of damaging the compressor. Look for the causes of
the increase in the compressor rpm
(damaged or pierced
SLSHVFORJJHG¿OWHUVHWF
$WWKHDLULQOHWWKHFRQWLQXRXVHMHFWLRQSUH¿OWHUVHSDUDWHVDQG
UHPRYHV PRVW RI WKH VXVSHQGHG SDUWLFOHV GXVW LQVHFWV VDQG
VRRWWKHUHE\SURORQJLQJWKHGXUDWLRQRIWKHDLU¿OWHU
&OHDQWKHHQWLUHSUH¿OWHUDWWKHHQGRIHDFKZRUNVHDVRQ
Before starting the compressor
&KHFNWKHIURQWDQGUHDURLOOHYHOV
&KHFNWKDWWKHUHDUHQRREVWUXFWLRQVLQWKHHPSW\OLQHDQGLQWKH
SUHVVXUHOLQH
Carefully follow the instructions in the USE and MAINTENAN-
CE manual of the CT50 JUROP compressor.
ATTENTION
Do not perform maintenance on the compressor when it is
very hot; wait until it has cooled down.
Summary of Contents for CHRONO 300
Page 4: ...4 cod G19504810...
Page 70: ...70 cod G19504810 Notes...
Page 71: ...71 cod G19504810 Notes...
Page 72: ...72 cod G19504810...
