English
48/172
English
49/172
In you slip or fall onto the ground or into a hole,
immediately let go of the throttle lever.
Do not solely rely on the safety devices that are
integrated on this tool.
Do not use the machine if you are feeling
tired, unwell or under the effects of
medication, intoxicating substances or
alcohol.
It is necessary to pay special attention to the
precautions if the machine is used during or just after
rain, since the ground could be slippery.
Do not cut above shoulder height
This product must never be used at night, in foggy
conditions or when visibility is limited and it is difficult
to see the working area clearly.
Lack of sleep, fatigue or physical tiredness can cause
accidents and harm.
Do not use the tool for longer than 10 minutes at a
time and rest for 10-20 minutes between sessions.
Never leave the machine running without surveillance.
Do not allow anyone to enter the area in which you
are working. This work perimeter is 15 meters and is
a danger zone.
Never start or operate the engine in a
closed room or building. The exhaust gases
contain dangerous carbon monoxide.
If the concentration of gases produced by inadequate
ventilation, remove from the work area everything that
impedes the flow of clean air for better ventilation
and do not return to work in the area unless you
have properly ventilated the area and be sure that
ventilation is enough that it does not happen again.
A firm grip will help to reduce kickback and
will help to keep the tool under control.
Take extreme care when cutting branches or
young trees, small splinters could get caught in the
chain and then be sent flying in the air, hitting or
unbalancing you.
When cutting a branch which is under tension, pay
special attention to the possibility of the branch
bouncing back, in order to avoid being hit by the
branch when the tension is freed.
Check the tree to ensure there are no dead branches
that can fall whilst you are working.
To avoid possible accidents, make sure the cutting
area is kept clear of obstacles at all times.
When using the chainsaw, do not allow the tip of the
bar to touch any other tree trunk or obstacle that may
be found near the area where the cutting is being
carried out.
Cutting with the engine at high revolutions.
Keep the chain sharpened by following the instructions
contained in this manual.
Never touch parts which reach high
temperatures during the starting up or
the operating of the engine such as, for
example, the exhaust silencer, the high voltage cable
or the spark plug.
Always carry out adjustments with the machine on a
flat and clear surface.
Do not use any accessory with the machine, apart
from those recommended by our company, as this
could result in serious injury to both the operator
of the machine and the people near. It could also
damage the machine.
Summary of Contents for MONTANA FIRST
