background image

Part # P128 Rev 5 (05/29/09)

Page 9

Stainless Steel

Stainless steel should be cleaned using a mild detergent, 
a soft cloth and hot water. If it is necessary to use a non-
metallic scouring pad, always rub in the direction of the grain 
in the metal to prevent scratching. Wash a small area at a 
time and rinse the washed area with a clean sponge dipped 
into a disinfectant and wipe dry with a soft clean cloth before 
it can dry.

Use only stainless steel, wood or plastic tools to scrape 
off heavy deposits of grease or oil. Do not use ordinary 

TUFFMTDSBQFSTPSLOJWFTBTQBSUJDMFTPGJSPONBZCFDPNF

embedded and rust.

NEVER USE STEEL WOOL

Griddles

Preparing A New Griddle

1.  Remove the protective coating on the surface using a 

mild detergent.

2.  Thoroughly rinse the griddle with vinegar and water 

TPMVUJPO DVQWJOFHBSQFSRVBSUPGXBUFSBOEESZ

Seasoning the Griddle

1.  Using a clean cloth, rub a thin and even layer of oil into 

the griddle surface. Oil should be an unsalted shortening 

PSIJHIUFNQFSBUVSFDPPLJOHPJM

2.  Set the griddle thermostat to 66°C (150°F) and heat the 

griddle surface until the oil begins to caramelize (turn a 
golden brown colour).

3.  Scrape off the caramelized oil with a standard spatula.

4.  Repeat step 1, and set the griddle thermostat to 135°C 

(275°F).

5.  Repeat step 2 & 3. The griddle is now seasoned and ready 

for use.

Cleaning Instructions (After Each Use)

1.  Using a traditional 64mm-76mm (2 ½”-3”) scraper or 

spatula scrape the griddle surface (to remove food 
particles and oil residues) towards the grease trough 

VTJOHFWFOGSPOUUPCBDLTUSPLFT%FQPTJUEFCSJTJOUPUIF

chute.

2.  Using a clean cloth, rub a thin and even layer of oil into 

the griddle surface.

3.  Remove the grease drawer, empty and wash thoroughly 

with soap & water. Replace.

Cleaning Instructions (For Heavy Build Up)

NOTE:  After using cleaners & grease cutter, re-season the 
griddle.

Apply to a warm griddle for best results.

1.  Using a traditional 64mm-76mm (2 1/2”-3”) scraper 

or spatula scrape the griddle surface (to remove food 
particles and oil residues) towards the grease trough 

VTJOHFWFOGSPOUUPCBDLTUSPLFT%FQPTJUEFCSJTJOUPUIF

chute.

2.  Apply griddle cleaner evenly over the griddle surface and 

let sit as directed. Follow the procedures on the label of 
the specific cleaning product.

3.  Using a traditional scraper or spatula, slosh around the 

griddle cleaner to remove the build up.

4.  Scrape the griddle surface towards the grease trough 

VTJOHFWFOGSPOUUPCBDLTUSPLFT3FQFBUTUFQJG

necessary.

5.  Using a mild detergent, clean the surface and rinse 

thoroughly with a water and vinegar solution. Dry 
griddle.

6.  Using a clean cloth rub a thin and even layer of oil into 

the griddle surface.

7.  Re-season the griddle as detailed above. The griddle is 

now ready for use.

MAINTENANCE & CLEANING

Summary of Contents for CG-24R

























Reviews: