GB
- 25 -
100:1. If insu
ffi
cient lubrication is the cause of en-
gine damage, it voids the manufacturer’s engine
warranty for that occurrence.
Gasoline and Oil Mix 40:1 Oil Only
Recommended fuels
Some conventional gasolines are being blended
with oxygenates such as alcohol or an ether com-
pound to meet clean air standards. Your engine is
designed to operate satisfactorily on any gasoline
intended for automotive use including oxygenated
gasolines. It is recommended to use unleaded
petrol as fuel.
Lubrication of chain and chain bar
Whenever you re
fi
ll the fuel tank with petrol you
must also top up the level of chain oil in the chain
oil tank. It is recommended to use standard chain
oil.
Engine pre-start checks
Danger:
Never start or operate the saw unless
the bar and chain are properly installed.
1. Fill the fuel tank (A) with correct fuel mixture
(Fig. 8).
2. Fill the oil tank (B) with chain oil (Fig. 8).
3. Be certain the chain brake is disengaged (C)
before starting unit (Fig. 8).
Once you have
fi
lled the chain and oil tank, tigh-
ten the tank cover securely by hand. Do not use
any tools to do so.
6. Operation
Before you use the equipment, check it for dama-
ge. If you discover any damage, do not use it. The
equipment may be started only when the chain
brake is engaged. The chain brake is engaged
when the brake lever is pressed forward and the
mechanism (Fig. 7B/Item A) is visible.
6.1 Starting the engine
1. Set the On/O
ff
switch (A) to “On (I)” to start
the machine (Fig. 9A).
2. Pull out the throttle lever (B) (Fig. 9B) until it
locks.
3. Push the primer bulb (C) 10 times (Fig. 9C).
4. Place saw on a
fi
rm,
fl
at surface. Hold saw
fi
rmly as shown. Pull starter rapidly 2 times.
Beware of moving chain! (Fig.9D)
5. Push in the throttle lever (B) as far as it will go
(Fig. 9B).
6. Hold
saw
fi
rmly and pull starter rapidly 4
times. Engine should start (Fig. 9D).
7. Let the engine run for 10 seconds to warm up.
Press the throttle lever (D) brie
fl
y, the engine
will go to “idling” speed (Fig. 9E).
If engine failed to start, repeat these instructions.
Note:
Always pull the starter cable slowly until
you feel the initial resistance before you then pull
it quickly to start the engine. Do not allow the star-
ter cable to whip back of its own accord.
6.2 Restarting a warm engine
1. Make sure the switch is in the ON position.
2. Pull the starter rope rapidly 6 times. The engi-
ne should start.
6.3 To stop engine
1. Release trigger and allow engine to return to
idle speed.
2. Move STOP switch down to stop engine.
Note:
To stop the engine in an emergency, activa-
te the chain brake and switch the ON/OFF switch
to “Stop (0)”.
6.4 General cutting instructions
Danger:
Felling trees is prohibited without the
necessary training!
Felling
•
Felling is the term for cutting down a tree.
Small trees up to 6-7 inches (15-18cm) in
diameter are usually cut in a single cut. Larger
trees require notch cuts. Notch cuts determi-
ne the direction the tree will fall.
•
A retreat path (A) should be planned and
cleared as necessary before cuts are started.
The retreat path should extend back and dia-
gonally to the rear of the expected line of fall,
as illustrated in Fig. 11.
Anl_GMSE_2245_SPK7_Teil1.indb 25
Anl_GMSE_2245_SPK7_Teil1.indb 25
05.08.14 10:17
05.08.14 10:17
