background image

1. DELCOS 3100 Electronics 

37

 

1.7.10

 

Automatic restart after power failure 

 

Danger  

In this operating mode, the compressor can start 
automatically at any time! 

You can activate or deactivate automatic restart in the 
[CONTROL MENU] (see Chapter 1.3.2). 

After a power failure lasting no longer than approx. 
2 seconds, the compressor is automatically restarted if 
it was switched on, i.e. in operation (standby), before 
voltage failed 

Power failures lasting longer than 2  seconds produce 
the [POWER LOSS] message and [AUTO RESTART] 
does not take place. 

The [POWER LOSS TIME] menu option (see Chapter 
1.3.2) can be programmed to between 2 and 999 
seconds.  

In addition, you can also program a start-up delay of 
1 to 60 seconds to ensure staggered start-up in the 
case of multiple-compressor stations – to ease the 
strain on the power supply system. The plaintext field 
then shows:  

[WARNING START IN xx s]. 

In remote-controlled operation, restarting also requires 
the [REMOTE ON]. In timer-controlled operation, the 
timer enable must be given. 

 

1.7.11

 

Unlimited automatic restart after 
power failure 

The control system is able to conduct an automatic 
restart after a power failure of any length. 

For this purpose, you must have read the following 
safety information and, by entering a code, enable 
unlimited automatic restart.  

Please request the required code from the Gardner 
Denver customer service. 

 

Danger   

In this operating mode, the compressor can start 
automatically at any time and after power failure of 
unlimited duration. Check the safety regulations 
applicable in your country (e.g. EN1012-1, EN60204) 
to ascertain whether you are allowed to perform an 
unlimited automatic restart and establish which 
safety precautions must be taken. 

At all events, provide the compressor with warning 
signs, keep the compressor room locked and 
instruct personnel.  

Install the main switch prescribed under EN60204 
and affix appropriate warning signs there.  

This is how to enable unlimited automatic restart: 

1.  Press the    code key 

2.  Enter the code 

3.  Press the   key to accept the code you have set  

After enabling, you can now also program the menu 
option for max. failure time to [POWER LOSS TIME–s]. 
This corresponds to unlimited automatic restart.  

Entering the code a second time withdraws enabling.  
 

 

1.7.12

 

RS485 communication 

DELCOS 3100’s serial interface provides the capability 
of using two protocols. In addition, it is also possible to 
set different baud rates (4800, 9600, 19200 baud) and 
user addresses. These settings are made in the 
[CONTROL MENU] menu.  

The DELCOS protocol is used together with the 
Gardner Denver profibus module. Using the profibus 
module, DELCOS 3100 can be connected to a profibus 
master (e.g. PLC).  

Modbus interfaces and the associated drivers are 
available for almost all well-known makes of 
programmable logic controllers and PC visualisation 
software. 

Summary of Contents for DELCOS 3100

























































Reviews: