background image

1800 909 909 

www.globalpowerbrands.com      email: [email protected] 

AFTER SALES SUPPORT 

43669

17

Instructions

5

8. Allow the engine to run for 10 seconds to let it warm up. 
9. To increase the engine speed, increase pressure on the throttle trigger. To decrease 

the engine speed, reduce pressure on the throttle trigger. Release throttle trigger 
(1) completely to return to idle.  

 Note. 

 If the motor stalls, move the choke back to the full choke position and 

repeat from point 4 unless the motor is already warm.  If already warm, start in 
the half or no choke position.

Stopping the blower

Stop the engine by pressing the On /Off switch on the symbol 
marked “O” to turn off the ignition.

Blowing

Start the blower engine, as previously described. Hold the 
blower firmly about 10–20 cm from the ground and move it in 
a sweeping motion from left to right, directing the debris to 
the desired location. 

•   Use low throttle settings when clearing lightweight materials from around lawns 

or shrubbery. 

•   Use medium to higher throttle settings to move lightweight grass or leaves from 

driveways or paths. 

•   Use full throttle when moving heavy loads such as dirt or snow. 

 IMPORTANT. 

 Blower noise increases at higher throttle settings. Always use the 

lowest throttle setting required to get the job done. 

•   Never operate the blower unless it is properly assembled and in good working 

condition. 

•   Never operate the blower without a properly functioning muffler and spark 

arrestor installed. 

Use of the petrol blower 

•   The petrol blower vac can efficiently move a wide variety of debris ranging from 

grass clippings to gravel. As a general rule try to operate the blower at the lowest 
throttle setting necessary to get the job done. 

•   Prior to use of the blower ensure you have read and understood this instruction 

manual. 

Summary of Contents for PBV26CC

























Reviews: