manualshive.com logo in svg

Fujitsu MHT2040BH, Product Manual

The Fujitsu MHT2040BH is a reliable and high-performance hard drive designed for your storage needs. To fully utilize its capabilities, make sure to refer to the product manual. At manualshive.com, you can easily download the manual for free, ensuring seamless integration and optimal usage of this exceptional product.

Share
Download
background image

 

5.3   Host Commands 

C141-E203-01EN 5-117 

• 

SET MAX UNLOCK (Features Field = 03h)  

This command requests a transfer of single sector of data from the host, and 
defines the contents of SET MAX ADDRESS password.   

The password supplied in the sector of data transferred shall be compared with the 
stored password. 

If the password compare fails, the device returns command aborted and decrements 
the Unlock counter, and remains in the Set Max Lock state.  On the acceptance of 
the SET MAX LOCK command, the Unlock counter is set to a value of five.  
When this counter reaches zero, then SET MAX UNLOCK command returns 
command aborted until a power cycle. 

If the password compare matches, then the device makes a transition to the Set 
Max Unlocked state and all SET MAX commands will be accepted. 

• 

Error reporting conditions 

(1)  The device is in Set Max Locked mode or Set Max Freeze Locked mode  

(ST = 51h, ER = 04h). 

(2)  The device is in Set Max Unlocked mode (ST = 51h, ER = 04h). 

(3)  The SET MAX ADDRESS (EXT) command has been issued  

(ST = 51h, ER = 04h). 

(4)  A SATA communication error occurred (ST = 51h, ER = 14h). 

 

At command issuance (Shadow Block Registers setting contents) 

CM 

1 1 1 1 1 0 0  1 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

03 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

CH 

CL 

SN 

SC 

ER 

xx 

xx 

xx 

xx 

xx 

Error information 

Summary of Contents for MHT2040BH









































































































































































































































































Reviews:

No comments

Related manuals for MHT2040BH

Quantum Scalar 50 Quick Start Manual preview
Scalar 50
Brand: Quantum Pages: 42
Quantum Scalar i500 Getting Started Manual preview
Scalar i500
Brand: Quantum Pages: 148
QNAP TVS-73e Series Quick Installation Manual preview
TVS-73e Series
Brand: QNAP Pages: 24
RAID Falcon 24-Bay Installation And Hardware Reference Manual preview
Falcon 24-Bay
Brand: RAID Pages: 108
LaCie FastKey User Manual preview
FastKey
Brand: LaCie Pages: 54
StarTech.com RAIDBAY3 Installation Manual preview
RAIDBAY3
Brand: StarTech.com Pages: 7
G&T SALES Fast Framer Quick Start Manual preview
Fast Framer
Brand: G&T SALES Pages: 2
SilverStone TOWER STORAGE TS421S Manual preview
TOWER STORAGE TS421S
Brand: SilverStone Pages: 52
P.V. Supa Libcabinet Manual preview
Libcabinet
Brand: P.V. Supa Pages: 54
P.Lindberg 9065890 Manual preview
9065890
Brand: P.Lindberg Pages: 22
IBM Storwize V5000E Quick Installation Manual preview
Storwize V5000E
Brand: IBM Pages: 120
G-Technology G-RAID mini 1TB Installation Manual preview
G-RAID mini 1TB
Brand: G-Technology Pages: 13
Panasonic RP-SM16GFE1K Operating Instructions Manual preview
RP-SM16GFE1K
Brand: Panasonic Pages: 18
Fujitsu FD-1100MT User Manual preview
FD-1100MT
Brand: Fujitsu Pages: 40
Fujitsu ETERNUS2000 100 Manual preview
ETERNUS2000 100
Brand: Fujitsu Pages: 21
Fujitsu FibreCAT S80 Manual preview
FibreCAT S80
Brand: Fujitsu Pages: 90
Fujitsu GP5-HDH8B User Manual preview
GP5-HDH8B
Brand: Fujitsu Pages: 12
Fujitsu GP5-HD6G1 User Manual preview
GP5-HD6G1
Brand: Fujitsu Pages: 14

Brands by name

Popular brands

Load more brands