Fujitsu MHT2040BH Product Manual Download Page 176 | Manualshive

Page: 176 / 264

background image

Interface

5-102 C141-E203-01EN

(31) SECURITY SET PASSWORD (X’F1’)

This command enables a user password or master password to be set.

The host transfers the 512-byte data shown in Table 5.26 to the device. The device
determines the operation of the lock function according to the specifications of the
Identifier bit and Security level bit in the transferred data. (Table 5.27)

Issuing this command in LOCKED MODE or FROZEN MODE returns the
Aborted Command error.

Table 5.26 Contents of SECURITY SET PASSWORD data

Word Contents

0 Control

word

Bit 0 Identifier

0 = Sets a user password.

1 = Sets a master password.

Bits 1 to 7 Reserved

Bit 8 Security level

0 = High

1 = Maximum

Bits 9 to 15 Reserved

1 to 16

Password (32 bytes)

17

Master password version number

18 to 255

Reserved

Table 5.27 Relationship between combination of Identifier and Security level, and

operation of the lock function

Identifier Level

Description

User

High

The specified password is set as a new user password. The
lock function is enabled after the device is turned off and
then on. LOCKED MODE can be canceled using the user
password or the master password already set.

Master

High

The specified password is set as a new master password.
The lock function is not enabled.

User

Maximum

The specified password is set as a new user password. The
lock function is enabled after the device is turned off and
then on. LOCKED MODE can be canceled using the user
password only. The master password already set cannot
cancel LOCKED MODE.

Master

Maximum

The specified password is set as a new master password.
The lock function is not enabled.

«
...
174
175
176
177
178
...
»

Summary of Contents for MHT2040BH









































































































































































































































































Reviews:

No comments

Related manuals for MHT2040BH

Brand: Facom Pages: 4

Rapid Mount 9909-3-02

Brand: Weather Guard Pages: 9

Brand: U-Line Pages: 6

BAULE EVO 80 BAULE EVO 120

Brand: garofalo Pages: 16

Brand: Premio Pages: 2

TotalStorage Network Attached Storage 300G

Brand: IBM Pages: 86

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Brand: LaCie Pages: 74

Brand: IBM Pages: 21

Brand: S&C Pages: 42

Brand: Curtiss-Wright Pages: 140

Brand: Enhace Pages: 6

Brand: Fantec Pages: 73

Brand: Westfalia Pages: 15

Brand: Atmel Pages: 30

Brand: Karibu Pages: 47

VTrak D5000 Series

Brand: Promise Technology Pages: 245

Brand: QNAP Pages: 12

Brand: QNAP Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands