Fujitsu MHT2040BH Product Manual Download Page 36 | Manualshive

Page: 36 / 264

background image

Device Overview

1-14 C141-E203-01EN

1.12 Interface Power Management (IPM)

1.12.1 Host-initiated Interface Power Management (HIPM)

When the disk drive is waiting for commands, it can enter one of three IPM
modes as requested by the host. The three IPM modes are:

1) Partial mode:

PMREQ_P is sent when the host requests the Partial mode.

2) Slumber mode: PMREQ_S is sent when the host requests the Slumber mode.

3) Active mode:

When the serial ATA interface is in active state.

There are three interface (I/F) power states: Active, Partial, and Slumber. As
requested by the host, the disk drive switches its I/F power state from the Active
state to the Partial state, or from the Active state to the Slumber state.

1.12.2 Device-initiated Interface Power Management (DIPM)

If this function is enabled by Set Features command, the disk drive shifts to two
kinds of IPM modes automatically under the Idle condition.

1) Partial mode:

PMREQ_P is sent when the disk drive requests the Partial

mode.

2) Slumber mode: PMREQ_S is sent when the disk drive requests the Slumber

mode.

I/F power states

1) Active

state

The SATA interface is active, and data can be sent and received.

2) Partial

state

The SATA interface is in the Power Down state. In this state, the interface is
switched to the Partial state when a PMREQ_P signal is received from or sent
to host. Because the return time to the Active state from the Partial state is
specified as within 10

µ

s, the degree of the I/F Power Save mode is shallow

so that this recovery time is satisfied.

3) Slumber

state

The SATA interface is in the Power Down state. In this state, the interface is
switched to the Slumber state when a PMREQ_S signal is received from or
sent to host. Because the return time to the Active state from the Slumber
state is specified as within 10 ms, the degree of the I/F Power Save mode is
deep so that this recovery time is satisfied.

«
...
34
35
36
37
38
...
»

Summary of Contents for MHT2040BH









































































































































































































































































Reviews:

No comments

Related manuals for MHT2040BH

TotalStorage DS4800

Brand: IBM Pages: 250

TotalStorage DS4800

Brand: IBM Pages: 234

Brand: IBM Pages: 136

System Storage DS5020

Brand: IBM Pages: 31

Netfinity EXP300

Brand: IBM Pages: 93

Brand: IBM Pages: 270

Ultrastar 36LZX

Brand: IBM Pages: 2

DCAS-32160 - Ultrastar 2.1 GB Hard Drive

Brand: IBM Pages: 232

System Storage TS3310

Brand: IBM Pages: 531

Brand: HOMCOM Pages: 33

B. spaces Tidy Toybox

Brand: Maison Battat Pages: 2

SmartStore SM2020

Brand: Riverlea Pages: 16

TS-401T Turbo Server

Brand: QNAP Pages: 8

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands