Fujitsu MHT2040BH Product Manual Download Page 248 | Manualshive

Page: 248 / 264

background image

Glossary

GL-2 C141-E203-01EN

MTTR

Mean time to repair. The MTTR is the average time required for a service person
to diagnose and repair a faulty drive.

PIO (Programmed input-output)

Mode to transfer data under control of the host CPU

Positioning

Sum of the seek time and mean rotational delay

Power save mode

The power save modes are idle mode, standby mode, and sleep mode.

In idle mode, the drive is neither reading, writing, nor seeking data. In standby
mode, the spindle motor is stopped and circuits other than the interface control
circuit are sleeping. The drive enters sleep mode when the host issues the SLEEP
command.

Reserved

Reserved bits, bytes, and fields are set to zero and unusable because they are
reserved for future standards.

Rotational delay

Time delay due to disk rotation. The mean delay is the time required for half a
disk rotation. The mean delay is the average time required for a head to reach a
sector after the head is positioned on a track.

Seek time

The seek time is the time required for a head to move from the current track to
another track. The seek time does not include the mean rotational delay.

Status

The status is a piece of one-byte information posted from the drive to the host
when command execution is ended. The status indicates the command
termination state.

VCM

Voice coil motor. The voice coil motor is excited by one or more magnets. In
this drive, the VCM is used to position the heads accurately and quickly.

«
...
246
247
248
249
250
...
»

Summary of Contents for MHT2040BH









































































































































































































































































Reviews:

No comments

Related manuals for MHT2040BH

Hard Disk MAX Quadra

Brand: LaCie Pages: 2

8BIG RACK THUNDERBOLT 2

Brand: LaCie Pages: 28

SOHORAID ST4-TB3

Brand: Stardom Pages: 25

Brand: Zhejiang Longyard Trade Industrial Pages: 18

Brand: ClosetMaid Pages: 11

Brand: LaCie Pages: 4

Brand: P.Lindberg Pages: 22

Brand: HP Pages: 75

Brand: LaCie Pages: 26

Microdrive RHMD2G

Brand: Sony Pages: 2

Memory Stick PRO DUO MSX-M256S

Brand: Sony Pages: 2

Memory Stick MSA-32A

Brand: Sony Pages: 2

Memory Card DKA-MC10F

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 19

Brand: Sony Pages: 24

Brand: Sony Pages: 24

FLEXISTORE 1533

Brand: Asgard Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands