Fujitsu MHT2040BH Product Manual Download Page 152 | Manualshive

Page: 152 / 264

background image

Interface

5-78 C141-E203-01EN

(23) READ DMA (X’C8’ or X’C9’)

The READ DMA command reads data from sectors, starting from the sectors
specified in the Device/Head, Cylinder High, Cylinder Low, and Sector Number
fields and continuing for as many sectors as specified in the Sector Count field. A
value ranging from 1 to 256 can be specified for the number of sectors. In order to
specify 256, "00" must be set in the Sector Count field. For the protocol
concerning data transfers, see Section 5.4.4.

When the command is completed, either cylinder, head, and sector addresses (CHS
mode) or the logical block address (LBA mode) of the last sector is stored in the
Shadow Block Register.

If an error such as an uncorrectable disk read error is detected during execution of
the READ DMA command and continued operation not possible, the data transfer
stops after all data, including the data of the sector where the error was detected, is
transferred. The device notifies the host of the status by sending the Register DH
FIS. At this time, the number of remaining sectors including the sector where the
error was detected, and either cylinder, head, and sector addresses (CHS mode) or
the logical block address (LBA mode) of the sector where the error was detected
are stored in the Shadow Block Register.

The host system can select the DMA transfer mode by using the SET FEATURES
command, however, the transfer speed does not change.

•

Multiword DMA transfer mode 0 to 2

•

Ultra DMA transfer mode 0 to 5

•

Error reporting conditions

(1) A specified address exceeds the range where read operations are allowed

(ST = 51h, ER = 10h).

(2) The range where read operations are allowed will be exceeded by an address

during a read operation (ST = 51h, ER = 10h).

(3) An uncorrectable disk read error occurred (ST = 51h, ER = 40h).

(4) The sync byte indicating the beginning of a sector was not found

(ST = 51h, ER = 01h).

(5) A SATA communication error occurred (ST = 51h, ER = 0Ch).

(6) An error other than the above errors occurred (ST = 51h, ER = 04h).

«
...
150
151
152
153
154
...
»

Summary of Contents for MHT2040BH









































































































































































































































































Reviews:

No comments

Related manuals for MHT2040BH

Brand: CalDigit Pages: 21

FlashPen "Piko"

Brand: Hama Pages: 8

Tenus FlashPen USB 3.0

Brand: Hama Pages: 4

Dock & Done S-DVD-100

Brand: Olympus Pages: 156

Brand: Global Industrial Pages: 7

Brand: SIP Pages: 6

Brand: Navisys Technology Pages: 21

MaxAttach NAS 4000

Brand: Maxtor Pages: 2

G-RAID mini 1TB

Brand: G-Technology Pages: 13

Brand: Ultra Products Pages: 1

Brand: Edsal Pages: 2

Brand: EditShare Pages: 112

Brand: Western Digital Pages: 4

Brand: Westfalia Pages: 6

SuperStorage SSG-136R-NR32JBF

Brand: Supermicro Pages: 75

Brand: Essential Garden Pages: 12

Brand: Think Tank Photo Pages: 2

Brand: SULO Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands