FUJIPLA AL-MEISTER ALM3230 Instruction Manual Download Page 4

Page: 4 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 4 of 68

SPECIFICATIONS

Feature:

Model ALM3230

Minimum

Maximum

Feeder Tray Capacity

1 page

200 pages (20# copy paper), less for thicker paper

Paper Width

8-1/8”

12.6”

Paper Length

6-1/2”

20” in normal mode, unlimited length in “LONG MODE”

Operating Temperature

170 degrees F

270 degrees F

Operating Speed (in. per min.)

ver 1.0 and 1.2 = 40 (fixed)

ver 2.1 = 28 – 42 (variable)

Finished Size (W x L) and

Cutting/Trimming

Methods/Sizes of Common

Paper Sizes

Letter (8.5” x 11”), Double Letter (11” x 17”), and “Digital” (12” x 18”) sizes are the

most common. An additional length of film margin can be retained on leading, and

trailing edges of up to .2” and 1.2” respectively.

Maximum Laminated Thickness 16mil (.016”) (including film thickness)
Exit Tray capacity

200 pages (20# copy paper laminated with 5mil film), less for thicker paper

Warm-up Time

Approx. 15 minutes

Power Source

AC 120V 60 Hz

Power Consumption

1200W, 10A

Laminator Dimensions

50.1"(W) X 24.8"(D) X 18.5"(H) including Feeder Tray, Feeder Tray Extension and Exit

Tray installed. (Not including Stand.)

Optional Stand Dimensions

19 (W) x 22 (D) x 24” (H) (Not including laminator)

Laminator Weight

97 LBS (Optional stand not included)

Optional Stand Weight

52.9 LBS (Laminator not included)

Environmental Restrictions

Within the range of 32F to 86F (68 +/- 40F recommended)/an altitude below 6600'.

Accessories

Feeder Tray -- Extension Feeder Tray -- Exit Tray -- Power Cord – Waste Collection Box

Summary of Contents for AL-MEISTER ALM3230





































































Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands

FUJIPLA AL-MEISTER ALM3230, Instruction Manual

Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands