FUJIPLA AL-MEISTER ALM3230 Instruction Manual Download

Page: 9 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 9 of 68

INSTALLATION

To avoid fire, electric shock, or any danger, do not install the machine in a place like:

In direct sunshine or near an
air conditioner.

In an extremely cold area.

In an extremely dusty area.

In an extremely humid/dry area.

In/near a heating appliance or extremely hot
area.

On an uneven or shaky floor.

POWER SUPPLY/GROUND WIRE

1. Use the appropriate power supply. Always connect to AC120V. Unstable voltage may cause electric shock,

fire, or damage to the machine. Always avoid using multiple outlet connections.

2. Pay attention to the amperage. Unless the amperage is enough, it may cause fire or malfunction. A

dedicated circuit is highly recommended.

3. Ensure a ground connection is correctly made to avoid any danger or electrical problems. Do not alter the

power cord.

4. Handle power cord with care.

Do not set the machine on the power cord. Do not pull the power cord forcibly.

Do not place the machine near heated equipment.

Damage to the power cord may cause fire, electric shock or damage to the machine and the operator.

Summary of Contents for AL-MEISTER ALM3230





































































Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands

FUJIPLA AL-MEISTER ALM3230, Instruction Manual

Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands