FUJIPLA AL-MEISTER ALM3230 Instruction Manual Download

Page: 11 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 11 of 68

REQUIREMENTS OF PAPER TO BE LAMINATED

Do not laminate:

• Money or valuable securities.

• Paper with staples.

• Magnets or magnetic documents.

• Flammable paper or material that is affected by heat such as vinyl chloride or polyethylene.

• Unique and irreplaceable documents.

• Paper thicker than 0.4mm including film thickness.

• Paper that discolors and changes in quality with heat such as thermal papers and crayoned pictures.

• Paper that contains a lot of moisture.

• Items other than paper (magnets, vinyl, etc.)

• Paper that is curved or has creases.

CLEANING OF EXTERIOR

Be sure that the machine is unplugged.

Before cleaning the machine turn off the power and let the machine cool down.

Wipe off stains with a soft cloth. When stains are persistent use a firmly squeezed soft cloth soaked in a small

quantity of water or detergent. Wipe off the residue of detergent with a cloth soaked in water.

USEFUL INFORMATION – FILM END

This model has a function that gives caution that the film will end soon. The final few feet of film has either

black colored film or the black colored tape on the film. Please note when doing continuous lamination, that

one or two sheets may be laminated with the black tape when film runs out. Therefore, in order to avoid this

problem, please check the remaining film amount on the display from time to time. It is recommended to

provide extra prints when laminating.

RECYCLING INFORMATION

This is a serviceable electronic device which contains components which should be replaced at the end of their

effective lives. You can help control emerging risks by disposing of the electronic device separately from your

domestic waste. Electric and electronic devices marked with a crossed out waste bin indicate that these

products should not be disposed of together with domestic waste as there may be a severe impact on the

environment as well as human health due to the possibly of hazardous materials.

Summary of Contents for AL-MEISTER ALM3230





































































Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands

FUJIPLA AL-MEISTER ALM3230, Instruction Manual

Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands