FUJIPLA AL-MEISTER ALM3230 Instruction Manual Download Page 16

Page: 16 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 16 of 68

2. NAMES AND FUNCTION (cont’d)

2-3. OPERATION PANEL

START

Press to start operation.

STOP

Press to stop operation.

RESET

Press to return to the operation mode and to reset the counter.

SCROLL (UP)

Press to raise cursor or the set value.

SCROLL (DOWN) Press to lower cursor or the set value.

MODE

Press to select MODE (menus) setting.

TEMP/SPEED

Press to select temperature or speed setting menus. Hold

continuously to see the current temperature.

POWER LAMP Indicates the power is on.

READY LAMP

Indicates that the set temperature has been achieved.

ECO LAMP

Lights during power saving mode.

ERROR LAMP

Lights when an operation error occurs. To aid in servicing note

the error message that is generated on the LCD display.

LCD DISPLAY

Shows status of settings, operation and errors.

Summary of Contents for AL-MEISTER ALM3230





































































Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands

FUJIPLA AL-MEISTER ALM3230, Instruction Manual

Search results

Summary of Contents for AL-MEISTER ALM3230

Reviews:

Related manuals for AL-MEISTER ALM3230

Brands by name

Popular brands