FujiFilm Frontier DE100 Operation Manual Download Page 25

Page: 25 / 188

- Frontier DE100 Operation Guide -

1-3

Rear

Product Description

1.1.1 Front panel open

The scrap paper box and inner cover have been removed; and the cartridge cover is open.

(10)

(11)

(12)

(13)

(10) Maintenance Cartridge

Container that holds the waste ink fluid.

(11) Ink Cartridges

Install four color ink cartridges.

(12) Inner Cover

Internal cover located between the scrap paper box and the roll paper
feeder.

(13) Roll Paper Feeder

Pull it to the front when removing the spindle unit.

1.2 Rear

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(1) Exhaust Vent

Exhausts air used to cool the printer internally.

(2) AC Inlet

Connects the power cord to the printer.

(3) USB Port

Connect the USB cable here.

(4) Airflow Vent

Takes in air to cool the printer internally.

(5) Lock Lever

Releases the lock for the rear cover.

(6) Rear Cover

Open when a paper jam occurs or to perform maintenance.

(7) Left Cover

Open when a paper jam occurs.

Summary of Contents for Frontier DE100





























































































































































































Search results

Summary of Contents for Frontier DE100

Reviews:

FujiFilm Frontier DE100, Operation Manual, Page: 25 / 188

Search results

Summary of Contents for Frontier DE100

Reviews: