FujiFilm BL-7000 Operation Manual Download Page 55

897N120551D

7-3

Chapter 7

 Storage and Maintenance

7.3  Storage

7.3.1  Storage of Light Source

Note

  Do not store the equipment in a place which does not meet the storage conditions. 

Store the equipment in a state where no force is applied to the cables. The equipment 
may be damaged.

Store the BL-7000 system in a place that meets the following conditions.

<Storage Environment> 

Note

  

<Operating Environment> 

Non-operating conditions

Temperature:

 

-20 to +60°C

Humidity:

 

 

10 to 90%RH 

(no dew condensation)

Pressure:

 

70 to 106 kPa

Temperature:

 

-10 to +45°C

Humidity:

 

30 to 95%RH 

(no dew condensation)

Pressure:

 

70 to 106 kPa

When the equipment has been out of use for a long period, check the operation again as performed at 
the installation.

 

VP-7000 Operation Manual, “Chapter 6 Preparation and Inspection of the System”

7.3.2  Storage of Water Tank

For details on how to store the water tank, refer to the operation manual of the water tank.

BL7000_E-50_897N120551D.indb   3

2016/09/05   14:06:18

Summary of Contents for BL-7000















































































Reviews: