Front Runner FAJK005 Fittings Manual Download Page 11 | Manualshive

Page: 11 / 23

Front Runner FAJK005 Fittings Manual Download Page 11

11

TAKE A TRIP

After your first adventure, check that all nuts, bolts, screws and fittings are tight. Re-tighten where
needed. You'll find a small amount of settling has happened.

Go on many more adventures, periodically checking all nuts, bolts, screws and fittings.

REMOVING YOUR RACK

Should you wish to remove your rack, you will need to plug the holes
you drilled in the roof (Step 3E), using the supplied Sealing Plugs (
from FAJK002 box, see image - 16 Supplied)

Remove the Tray, Front Uprights and the Tray Support Brackets, by
reversing the instillation procedure. Leave the Foam Washers and the
Aluminum Spacers in place. Screw in the Sealing Plugs reusing the
M6 Nyloc Nuts and Washers that held the Tray Support Brackets in
position.

(

)

A

(

)

A

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now's the time to visit your favorite Front Runner dealer in person or online.

(

)

A

Front Runner can not recommend a maximum weight carrying capacity. Please refer to your vehicle
manufacturer's recommendations.

REV_B03

«
...
9
10
11
12
13
...
»

Summary of Contents for FAJK005
























Reviews:

No comments