Fri-Jado Cold MCC, Service Manual

Page: 72 / 147

Page 72 Rev 3 Service Manual MCC Hot / Cold 2021
EWPlus EO LVD
9/12
PAR. DESCRIPTION RANGE M.U.
EWPlus 961 EO LVD EWPlus 971 EO LVD EWPlus 974 EO LVD
AP1 AP2 AP3 AP4 AP1 AP2 AP3 AP4 AP1 AP2 AP3 AP4
dFn Night mode offset. 0,1 ... 30,0 °C/°F 4,0 4,0 2,0 0,1 4,0 2,0 4,0 4,0 4,0 2,0 4,0 0,1
SPF Fast cooling setpoint. LSE ... HSE °C/°F 0,0 0,0 -0,5 -6,8 0,0 -0,5 -2,0 0,0 0,0 -0,5 -2,0 -6,8
dFF Fast cooling offset. 0,1 ... 30,0 °C/°F 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1 0,1
ESP Virtual door regulator's sensitivity. 0 ... 5 num 0 0 0 0 0 0 0 0 0 0 0 0
dOt Maximun Time Door Open with virtual door switch. 0 ... 255 sec 0 0 0 0 0 0 0 0 0 0 0 0
COMMUNICATION ("Add" folder) NOTE: all parameters available in the folder are not available in the vectors.
PtS (!) Communication protocol selection ( t = Televis; d = ModBus). t/d flag t t t
dEA (!) Device address: indicates the device address to the management protocol. 0...14 num 0 0 0
FAA (!) Family address: indicates the device family to the management protocol. 0...14 num 0 0 0
Pty (!) Modbus parity bit setting (
n
= none;
E
= even;
o
= odd). n/E/o flag n n n
StP (!) Modbus stop bit setting. 1b/2b flag 1b 1b 1b
DISPLAY ("diS" folder)
LOC
LOCk. Setpoint change shutdown. There is still the possibility to enter into
parameters programming and modify these, including the status of this
parameter to permit keyboard shutdown. n = no; y = yes.
n/y flag n n n n n n n n n n n n
PS1 PAssword 1. When enabled (
PS1 ≠ 0 ), this is the access key to level 1
parameters ( User ).
0...250 num 0 0 0 0 0 0 0 0 0 0 0 0
PS2 PAssword 2. When enabled (
PS2 ≠ 0 ), this is the access key to level 2
parameters ( Installer ).
0...250 num 15 15 15 15 15 15 15 15 15 15 15 15
ndt Display with decimal point.
n = no (integers only); y = yes (displayed with decimal point).
n/y flag y y y y y y y y y y y y
CA1
Calibration 1. Positive or negative temperature value added to the value
read by Pb1 . This sum is used both for the temperature displayed and for
regulation.
-12,0...12,0 °C/°F 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0
CA2
Calibration 2. Positive or negative temperature value added to the value
read by Pb2 . This sum is used both for the temperature displayed and for
regulation.
-12,0...12,0 °C/°F 0,0 0,0 0,0 0,0 0,0 0,0 0,0 0,0
ddL
Display mode during defrost.
0 = display the temperature read by Pb1 ;
1 = locks the reading on the temperature value read by Pb1 when
defrosting starts, and until the next time the SEt value is reached;
2 = displays the label deF during defrosting, and until the next time the
SEt value is reached. (or until Ldd has elapsed).
0/1/2 num 1 1 1 1 1 1 1 1 1 1 1 1
Ldd Timeout value for display unlock - dEF label 0 ... 255 min 30 30 30 30 30 30 30 30 30 30 30 30
dro
Select °C or °F for displaying the temperature read by probes. 0 = °C, 1 = °F.
NOTE: switching between °C and °F or vice-versa DOES NOT modify
the SEt, diF values, etc. (e.g. Setpoint=10°C becomes 10°F).
0/1 num 0 0 0 0 0 0 0 0 0 0 0 0
ddd Selection of type of value to be displayed.
0 = Setpoint; 1 = probe Pb1; 2 = probe Pb2; 3 = not used.
0/1/2/3 num 1 1 1 1 1 1 1 1 1 1 1 1
CONFIGURATION ("CnF" folder) - NOTE: the instrument must be switched off and then on again each time folder CnF parameter configuration is modified to prevent
any malfunction of the configuration and/or current timer operations.
H08
Stand-by operating mode.
0
= display switch off; the loads are active and the device reactivates the
display to signal any alarms;
1 = display switch off, loads and alarms stopped;
2 = display with OFF label, loads and alarms stopped.
0/1/2 num 2 2 2 2 2 2 2 2 2 2 2 2
H11
Configuration of digital input 1/polarity (D.I.1).
0 = disabled; ± 1 = defrost; ± 2 = reduced SET; ±3 = AUX;
± 4 = door switch; ± 5 = external alarm; ± 6 = stand-by (ON-OFF);
± 7
= pressure switch;
± 8
= deep cooling;
± 9
= energy saving;
±10 = door energy saving.
N.B.:
- the “+” sign indicates that the input is active if the contact is closed
- the “-” sign indicates that the input is active if the contact is open
-10 ... 10 num 10 0 9 9 10 9 10 10 10 9 10 9
H12 Configuration of digital input 2/polarity (D.I.2). Same as H11. -10 ... 10 num 0 0 0 0 0 0 0 0 0 0 0 0
H21
Configurability of digital output 1 (A).
0 = disabled; 1 = compressor; 2 = defrost; 3 = Fans;
4 = alarm; 5 = AUX; 6 = Stand-by; 7 = not used;
8 = condenser fan change rotation; 9 = retain valve.
0 ... 9 num 1 1 1 1 1 1 1 1 1 1 1 1
H22 Configurability of digital output 2 (B). Analogo a H21. 0 ... 9 num 5 5 2 3 3 3 2 8
H23 Configurability of digital output 3 (C). Analogo a H21. 0 ... 9 num 5 5 3 5
H25 Enable/Disable buzzer.
0 = disabled; 4 = enabled; 1-2-3-5-6-7-8-9 = not used
0 ... 9 num 0 0 0 0 0 0 0 0 0 0 0 0
H32
Configurability of DOWN key.
0 = disabled; 1 = defrost; 2 = AUX; 3 = reduced SET;
4
= Stand-by;
5
= deep cooling;
6
= energy saving
0 ... 6 num 0 0 0 0 2 2 0 0 2 2 0 2
H33 Configurability of ESC key. Same as H32 0 ... 6 num 4 4 4 4 4 4 4 4 4 4 4 4
H42 Evaporator probe present ( Pb2 ). n = not present; y = present. n/y flag y y y y y y y y
reL reLease firmware. Device version: read-only parameter / / / / / / / / / / / / / /
tAb tAble of parameters. Reserved: read-only parameter / / / / / / / / / / / / / /
COPY CARD ("Fpr" folder)
UL Upload. Programming parameter transfer from instrument to Copy Card. / / / / / / / / / / / / / /
Fr
Format Copy Card. Erase all data contained in the Copy Card.
ATTENTION: If parameter “Fr” is used, the data entered will be
permanently lost. This operation cannot be cancelled
/ / / / / / / / / / / / / /
FUNCTION ("FnC" folder)
The following function is available in the ‘ FnC ’ folder:
Function Function label ACTIVE Function label INACTIVE alarm signalled
Reset pressure switch alarms rAP rAP Led ON
NOTES: • To modify the status of a specified function press the ‘set’ button
• If the unit is switched off, the function labels go back to their default status.