Freefly Alta 8 Pro Manual Download Page 28

Page: 28 / 128

ALTA 8 Pro Ground Control Desktop and
Mobile App

Getting QGroundControl up and running is quick and easy! Use the ALTA Pro
QGroundControl program to change ALTA Pro’s parameters, monitor statuses, and set up
waypoint missions.

1. Download and install the application.

2. Start QGroundControl and ALTA Pro.
3. Connect your vehicle to the ground station device.

1. WiFi

1. To connect to ALTA Pro via WiFi, find the ALTA Pro’s WiFi connection by

searching for it in your device’s WiFi menu and then connect to it like you
would any other device.

2. You may have to

enable the WiFi feature

on ALTA Pro if it is your first time

connecting.

2. 900/868MHz

1. Simply plug in the 900/868MHz radio into your computer using the attached

USB cable. If ALTA Pro is turned on the two radio’s will automatically
connect!

Summary of Contents for Alta 8 Pro

































































































































Search results

Summary of Contents for Alta 8 Pro

Reviews:

Related manuals for Alta 8 Pro

Brands by name

Popular brands

Freefly Alta 8 Pro, Manual

Search results

Summary of Contents for Alta 8 Pro

Reviews:

Related manuals for Alta 8 Pro

Brands by name

Popular brands