background image

Sundance HD Edition Aerial Kit Contents List

Congratulations on your purchase of a DSLRPros

 

Sundance HD Edition Aerial Kit. 

Inside your P2 Tough Case you will find the following items with numbers that 
correspond to the kit image on the following page.

1. DJI Phantom 2 With 3-Axis Gimbal Pre-Installed 
2. Assorted A/C Power Cables With International Plug Adaptors
3. A/C Power Cable For TXS-8 Pro LiPo Charger
4. DSLRPros TXS-8 Pro LiPo Charger with Balance Board and Necessary Cabling
5. 2 Sets Of 4 9" Propeller Blades (Carbon Fiber and Plastic Blades Are Not To 

Be Used Together)

6. Set of 4 Propeller Guards and Propeller Guard Screws
7. Futaba Transmitter
8. LiPo Battery For Futaba Transmitter
9. Deluxe DSLRPros Radio Tx Lanyard
10. LiPo Battery Capacity Checker
11. 3 DJI Smart Flight Batteries (1 Shown)
12. 1 DJI Charging for Smart Flight Battery 
13. 1 Additional Charging Block for DJI Smart Flight Battery
14. DJI Smartphone Mount
15. HDMI Cable For GoPro To DJI Lightbridge Air System
16. Set of 2 DJI Lightbridge Air System Paddle Antennas & Air System Antennas
17. Set of 2 Antennas For DJI Lightbridge Ground System
18. DJI Lightbridge Ground System
19. DJI Lightbridge Transmitter Mount
20. DSLRPros LiPo Battery Guard Bag
21. Assorted Cables For DJI Lightbridge System (Please Refer To Your Lightbridge

Manual For Detailed Explanations For Each Of These Cables)

22.

Assorted Power Cables and International Plug Adaptors (Please Refer 

To Your Lightbridge Manual For Detailed Explanations For Each Of These 
Power Cables)

Summary of Contents for Cannes HD Edition Aerial Kit













Reviews: