background image

2

MR-8mkII Owner’s Manual (Safety instructions/Contents)

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER - SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

12. Power Cord Protection - Power supply cords should be

routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and
the point where they exit from the appliance.

13. Cleaning - The appliance should be cleaned only as

recommended by the manufacturer.

14. Nonuse Periods - The power cord of the appliance should

be unplugged from the outlet when left unused for a long
period of time.

15. Object and Liquid Entry - Care should be taken so that objects

do not fall and liquids are not spilled into the enclosure through
openings.

16. Damage Requiring Service - The appliance should be

serviced by qualified service personnel when:

A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance;

or

C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or

exhibits  a marked change in performance; or

E. The appliance has been dropped, or the enclosure damaged.

17. Servicing - The user should not attempt to service the

appliance beyond that described in the operating instructions.
All other servicing should be referred to qualified service
personnel.

18. The appliance should be situated away from drops of water

or spray of water.

19. Objects containing liquid such as vase must not be put on

the appliance.

20. The appliance is not completely isolated from the power

supply even if the power switch is at off position.

21. Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be
placed on the apparatus.

22. Only use attachments/accessories specified by the

manufacturer.

23. An appliance with a protective earth terminal should be

connected to a mains outlet with a protective earth
connection.

24. An appliance should be placed in a position where an AC

plug / inlet can be easily pulled out by hand.

25. Main plug is used as the disconnection device. It shall remain

readily operable and should not be obstructed during
intended use. To be completely disconnected the apparatus
from supply mains, the mains plug of the apparatus shall be
disconnected from the mains socket outlet completely.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE
OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

P O U R   E V I T E R   L E S   C H O C S   E L E C T R I Q U E S ,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU' AU FOND.

An appliance and cart combination should be moved with
care. Quick stops, excessive force, and uneven surfaces
may cause the appliance and cart combination to overturn.

7. Wall or Ceiling Mounting - The appliance should be mounted

to a wall or ceiling only as recommended by the
manufacturer.

8. Ventilation - The appliance should be situated so that its

location or position dose not interfere with its proper
ventilation.  For example, the appliance should not be situated
on a bed, sofa, rug, or similar surface that may block the
ventilation openings; or, placed in a built-in installation, such
as a bookcase or cabinet that may impede the flow of air
through the ventilation openings.

9. Heat - The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other
appliances (including amplifiers) that produce heat.

10. Power Sources - The appliance should be connected to a

power supply only of the type described in the operating
instructions or as marked on the appliance.

11. Grounding or Polarization - The precautions that should be

taken so that the grounding or polarization means of an
appliance is not defeated.

"WARNING"

"TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE."

SAFETY INSTRUCTIONS

1. Read Instructions - All the safety and operating instructions

should be read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions

should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the

operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should

be followed.

5. Water and Moisture - The appliance should not be used

near water - for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming
pool, and the like.

6. Carts and Stands - The appliance should be used only with

a cart or stand that is recommended by the manufacturer.

Summary of Contents for MR-8MKII



























































































































































Reviews: