1. Introduction
1.1 Transportation and storage
1.2 Preliminary steps
1.3 Initial setup
1.4 Important safety instructions
1.5 Standards
2. Installation and operation
2.1 Unpacking and inspection
2.2 UPS front and rear panel views
2.3 Single UPS installation
2.4 Output configuration
2.5 ForzaTracker monitoring software
3. Advanced operation
3.1 Description of buttons and functions
3.2 LED indicators and LCD panel
3.3 Audible alarm
3.4 Single UPS operation
3.5 Parallel operation
3.6 Abbreviations in the LCD display
3.7 UPS parameter settings
3.8 Operating mode/Status description
3.9 Fault codes
3.10 Warning indicators
4. Troubleshooting guide
5. Storage and maintenance
6. Technical specifications
Table of content
1. Introduction
Thank you for purchasing the Forza Atlas FDC 106K/110K Online UPS. To enjoy all the features and benefits of this unit,
please read and follow all installation and operation instructions thoroughly before unpacking, installing or operating this
device. After you have read this manual, keep it in a safe place for future reference.
The information contained in this manual covers the 6000VA and 10000VA uninterruptible power systems, their basic
functions, operating procedures, options available and troubleshooting guide. It also includes information on how to ship,
store, handle, and install the equipment.
1-1. Transportation and storage
• Transport the UPS system only in the original package to protect it against shock and impact.
• The UPS must be stored in a dry, well-ventilated area.
1-2. Preliminary steps
• Water condensation may occur if the UPS is unpacked in a very cold environment and then moved to a warmer
location.
• The UPS must be thoroughly dry before being installed. Failure to do so may increase the risk of electric shock.
• Do not install the UPS system near water or in moist environments.
• To reduce the risk of overheating, do not cover the cooling vents in the UPS housing.
• Avoid exposing the UPS to direct sunlight or installing the unit near heat-emitting appliances, such as electric heaters or
furnaces.
1-3. Initial setup
• Do not connect appliances or equipment that may overload the UPS system (such as big motor-type equipment) to the
UPS output sockets or terminal.
• Place cables in such a way that no one can step on or trip over them.
• Do not block air vents in the housing of UPS. The UPS must be installed in a location with good ventilation. Ensure enough
space on each side for ventilation.
• The UPS is provided with an earthed terminal. Equipotential earth bonding to the external UPS battery cabinets must
be provided if such configuration is used.
• The UPS can be installed only by qualified maintenance personnel.
• These UPS units are extremely heavy. Caution should be taken in moving and positioning equipment.
• An appropriate disconnect device as short-circuit backup protection should be provided in the building wiring installation.
• An integral single emergency switching device which prevents further supply to the load by the UPS in any mode of
operation should be provided in the building wiring installation
• Connect the earth before connecting the unit to the building wiring terminal.
• Installation and wiring must be performed in accordance with local electrical regulations and laws.
1-4. Important safety instructions
• Do not disconnect the earth conductor cable on the UPS or the building wiring terminals at any time since this would
cancel the protective earth of the UPS system and of all connected loads.
• In order to provide security and safety measures according to NFPA under 70 NEC article 250.20(D), the Neutral output is
internally grounded to the chassis of the UPS as a grounding system.
• The UPS system features its own, internal current source (batteries). The UPS output sockets or output terminals block
may be electrically live even if the UPS system is not connected to the building wiring outlet.
• In the event of an emergency, pull the EPO cable if in default mode or press the switch connected to the EPO if that option
is installed. Then disconnect the power from the AC mains to properly disable the UPS.
• Do not allow any kind of liquid or foreign object to enter this UPS unit. Do not place beverages or any other containers with
liquid on or nearby the unit.
• The UPS can be operated by any individuals with no previous experience.
