fortessa DIGI-2, Technical Manual

Page: 7 / 80

TM
5 TM
Digital call FT3340
Arrange the modules only as indicated in the following drawing.
1) KEY FUNCTIONS
INTRODUCTION
The digital call module FT3340 can be used in audio and video settings, is fitted with a
name directory to store a list of user names and with an alphanumerical keypad to call
the door entry phone users by entering the code which identifies them. The main
characteristics are as follows:
• Memory capacity: 400 names of 18 alphanumerical characters.
• Graphic display with 128x64 dots/pitch resolution.
• 2 call management modes : Standard or indirect code .
• Entering the name list ( Download ) by means of programmer FT1230 or by means of
connection with a PC fitted with software FT1249/A.
• Entering the names by means of connection with the PC can be done over an RS232
line or over an RS485 line by means of the interface card FT1319.
• Reading ( Upload ) of the name list stored in the directory module by means of
connection with a PC fitted with software FT1249/A.
• Access control with the possibility of storing up to 300 password codes to activate the
relay in the porter module, typically used as a door opener.
• Possibility of displaying the graphic interface messages in one of the 9 languages
available.
CALL – SELECT MENU
BACK: Scrolls the user list in
decreasing alphabetical order
FORWARD: Scrolls the user list
in increasing alphabetical order.
SEARCH FOR NAME - EXIT MENU
CALL -
LOCAL DOOR OPENING
CANCEL CHARACTER
or CALL
INITIAL CONDITION
3) SETTING THE LANGUAGE
3A) THE FIRST TIME THE MODULE IS TURNED ON, THE LANGUAGE HAS NOT YET
BEEN SELECTED:
On power up SELECT LANGUAGE:
*ITALIAN
ENGLISH
Scroll the list by means
of the
▲▼
keys.
To select the language
required, press
.
* ITALIAN
ENGLISH
FRANCAIS
The DEFAULT item sets
the ITALIAN language.
The next time the
module is turned on,
selection of the language
is requested again.
ON DISPLAY DESCRIPTION OPERATION
TEST DESCRIPTION
4) SELF – DIAGNOSIS
On power up, the apparatus carries out a diagnostic test of the connections to check correct
communication with porter module FT1602/FT4660 and with the keypad module which
makes up FT3340. If the wordi OK appears next to the item, then it has passed the test,
otherwise, if the word FAILED appears it has failed the test.
On completion of the Self-Diagnosis mode, press the
▼
key to put the module in the into its
normal mode of operation.
The table summarising the meaning of the single tests is given below:
INITIALIZING
SPEAK. SERIAL
MODE
Check the EEPROM which contains the
user name list. If the test fails, the module is faulty.
If the test fails, check correct serial connection
with porter module FT1602 / FT4660 .
Check presence of the alphanumerical keypad which
makes up FT3340. If the wording FT3342 appears next to
the description, correct connection between the alphanu-
merical keypad and the directory module must be checked.
2) ACCESSING THE CONFIGURATION STAGE
Powered up with PR
terminal connected
to terminal - .
Or:
During normal
operation press
,
insert the supercode
and confirm
pressing .
The module is in
programming mode:
to select the menu
▲▼
to scroll the menus.
to return to the
previous menu.
NAME DIRECTORY
ACCESS CONTROL
SETTINGS
ON DISPLAY DESCRIPTION OPERATION
3B) CHANGING THE LANGUAGE SET PREVIOUSLY:
Access to the configuration
stage has been carried out
(see point 2). NAME DIRECTORY
ACCESS CONTROL
SETTINGS
SELECT LANGUAGE:
*ITALIAN
ENGLISH
SELECT LANGUAGE:
ITALIAN
*ENGLISH
The default language
on power up is Italian.
The language set
is marked by an asterisk
on the left-hand side.
When repowered
the lanuage resets
to Italian by default.
Select the
SETTINGS /
SELECT LANG. menu.
Scroll the list by means
of the
▲▼
keys.
To select the language
required, press
.
ON DISPLAY DESCRIPTION OPERATION