Formulatrix NT8 User Manual Download | Manualshive

Page: 76 / 79

background image

72

Items

Description

Low Volume Tips

LV tips are sold by a case of 10 tip boxes that contain 384 tips each, or in a master
case that contains 10 cases of 10 tip boxes.

Disposable Protein Trays

Disposable protein trays come in packs of 100 trays.

LCP Starter Kit

The LCP starter kit includes one monoolein, an LCP syringe coupler, six short 26 gauge
needles, five LCP sandwich plates and seals, and two 100 µL syringes. Note: Your NT8
must be equipped with the LCP option in order for it to work with the LCP starter kit.

LCP Syringe Coupler

The LCP syringe coupler connects two LCP syringes.

Plate Copy Pipette Tips

Plate copy, or HV, tips are used for plate copy or daughter plate creation experiments.

Protein Block

A replacement part for the protein block that contains protein trays.

High Volume Protein Block

A replacement part or optional accessory to support experiments that need more protein
than a Low Volume Protein Block is designed to hold

Reference Plate

The reference plate is a clear plate that has crosshairs located at each corner. The
crosshairs are targets for you to use if you need to tune drop position. The NT8’s software
then determines the remaining drop positions from these four points

HD Seal Jig Transfer

The HD seal jig transfer is used to attach the HD seal to a microplate. It is used in hanging
drop experiments.

Ball Point Hex Keys

Also known as an Allen wrench, ball point hex keys are included for troubleshooting
purposes. They can also be used to tighten and loosen shipping bolts

«
...
74
75
76
77
78
...
»

Summary of Contents for NT8
















































































Reviews:

No comments

Related manuals for NT8

Brand: GE Pages: 2

Druck DPI 620 Genii

Brand: GE Pages: 154

Arize Element Top Light

Brand: GE Pages: 2

Brand: Datex-Ohmeda Pages: 104

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 166

Druck DPI 620 Genii

Brand: Baker Hughes Pages: 340

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: Palmer Pages: 2

Brand: Raytec Pages: 60

Brand: Vahterus Pages: 31

Brand: Balanced Body Pages: 4

Brand: Balanced Body Pages: 2

Reformer Trapeze Combination

Brand: Balanced Body Pages: 164

Brand: Wacker Neuson Pages: 50

Brand: Balanced Body Pages: 37

Ti-Max NLX nano

Brand: NSK Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands