Formulatrix NT8 User Manual Download

Page: 79 / 79

Button

Action

Turns on and off the wash pump and fills the chamber with the water.

Toggles the waste pump on and off and drains the chamber.

Turns on the humidifiers.

Switches you from automatic to manual control or vice versa for the humidifiers.

Displays the LCP Mixing Sequence Wizard (see Mixing LCP for more information).

Note

: This button displays only if you have the LCP attachment.

Adjusts the lever speed.

Note

: This button displays only if you have the LCP attachment.

Calibrates the Lipidic Cubic Phase (LCP) syringe.

Note: This button displays only if you have the LCP attachment.

Displays the settings and calibration operations.

Note

: Calibration operations should only be performed by Formulatrix support or advanced

users.

Displays options to open the data directory, open the config directory, or open the logs directory.

Enables you to send feedback on how to improve NT8 software.

Displays the NT8 software version and system information.

Displays the NT8 help file.

NT8 User's Guide | Appendix B: Toolbar Buttons

Summary of Contents for NT8















































































Search results

Summary of Contents for NT8

Reviews:

Related manuals for NT8

Brands by name

Popular brands

Formulatrix NT8, User Manual

Search results

Summary of Contents for NT8

Reviews:

Related manuals for NT8

Brands by name

Popular brands