Formulatrix NT8 User Manual Download | Manualshive

Page: 64 / 79

background image

60

You can create experiments in Rock Maker, and then dispense them with the NT8 using Rock
Maker Integration feature.

Prerequisites

●

You have created an experiment in Rock Maker. If you don't know how, please refer to
the "Experiment Design" section of the Rock Maker help file.

●

Rock Maker version 3.0.2.8 or newer.

Dispensing Rock Maker Experiments with the NT8

1.

Click the

Rock Maker Integration

tab . The editor screen displays (shown in step

2).

2.

Type your experiment barcode number in the

Experiment Barcode

field at the

upper-left corner of your screen or scan the barcode with a barcode
scanner (if it is available). When the barcode is validated, the Rock Maker experiment
information populates.

3.

Next, follow the on-screen instructions presented in the Instruction tab. The on-screen
instructions tell you to do some hardware preparations. For example, you may be told
to place the 96 1 Hampton LCP Sandwich on Microplate Station 1, attach the LCP
syringe to the LCP head, install microplates on the microplate stations, etc. See

Rock

Maker Integration Tab

.

Note:

The experiment details can only be changed or edited from the Rock Maker software.

«
...
62
63
64
65
66
...
»

Summary of Contents for NT8
















































































Reviews:

No comments

Related manuals for NT8

Brand: Fender Pages: 15

Brand: J D Squared Pages: 18

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: Bahco Pages: 9

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: Wahl Pages: 2

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: Malekko Pages: 2

Brand: Major Pages: 26

Brand: U-Line Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands