background image

5

Figure 3c

1. To enter the Autobatch mode press the “Batch    

Count” button and select “AUTOBATCH” by pressing 

the “-” button (Fig 3a).

2.  Once you have entered the Autobatch mode press 

the “+” or “-” button and “Sheets” (Fig. 3c) will blink.  

Press the “+” or “-” buttons to increase or decrease the 

number of sheets to be pulled.

3.  When the sheet number is set wait 5 seconds and 

“Sets” (Fig. 3c) will blink.  Press the “+” or “-” buttons 

to increase or decrease the number of sets to be 

pulled.

4. When the number of sets has been selected wait 5 

seconds and “Delay” (Fig. 3c) will blink. Press the “+” 

or “-” buttons to increase or decrease the time delay 

between the sets.

5.When the settings are correct press the “Start/Stop” 

to start.

NOTE: 

The system will cycle through the settings until 

the “Start/Stop” button is pressed.

NOTE:

 If a fault occurs during a set, the set will be 

completed when the fault is reset.

NOTE

: The batch counting program selected will 

remain on after the job is processed. You 

must

 press 

the Batch Counting button to turn off the light and 

cancel the batch count setting.

“Sheets” = Number of sheets of paper in a set

“Sets” = Number of sets to be processed

“Delay” = Time between each set

“C” = Total number of sheets processed

Figure 3b

DAILY MAINTENANCE

1.  It is recommended to let forms cool for one-half hour, from the laser printer, before folding and sealing.  This 

allows toner to set on the forms, and static electricity to discharge.  A 400 Series Jogger is recommended for 

best results.  The Jogger squares the forms and dissipates heat and static electricity created by laser printers.

2. If toner builds up on the metal sealer rollers, clean the rollers with a lint-free cloth dampened sparingly with a 

mild household cleaner.

3. Clean in-feed wheels and fold rollers with Formax recommended roller cleaner & rejuvenator to remove 

paper dust and toner.  A damp cloth with water is the best alternative. CAUTION: Do not use any chemicals 

other than the roller cleaner & rejuvenator or water.

Summary of Contents for AutoSeal FD 2052













Reviews: