manualshive.com logo in svg

Formax Atlas C150, Operating Instructions Manual, Page: 52 / 72

Share
Download
Formax Atlas C150 Operating Instructions Manual Download Page 52

 

 _________________________________________________________________________  

52  

3 

Fault Codes 

General 

When there is a misfeed or a fault condition in this machine, a message and a fault code will 

be displayed on the screen. Some fault codes may be rectified by the operator, while others 

may only be rectified by a certified service technician. 

 

 

NOTE: 

Clicking on the fault code will open a short description of the issue. 

To address fault codes other than those specified below, remove any paper in the paper path 

and power the system off and on again. If the fault code persists, contact a certified service 

technician. 
List of fault codes that can be rectified by the operator: 

FE-101 – Misfeed 

FE-102 – Double sheet 

FE-103 – Sheet too long 

FE-104 – Sheet too short 

FE-106 – Out of paper 

FE-108 – Paper table overloaded 

FE-109 – Too much paper 

FE-112 – Double sheet detector (DSD) blocked 

CR-201 – Sheet late from feeder output sensor Q7 to creaser input sensor Q20 

CR-202 – Creaser input sensor Q20 blocked 

CR-205 – Creaser 1 home sensor Q21 not activated 

CR-206 – Creaser 2 home sensor Q22 not activated 

CR-207 – Sheet late from creaser input sensor Q20 to creaser output sensor Q25 

CR-208 – Creaser output sensor Q25 blocked 

CR-209 – Clean creaser input sensor Q20 

 

 

Summary of Contents for Atlas C150









































































Reviews:

No comments