Ford 6.4L Power Stroke Manual Download

Page: 20 / 103

Cooling system

Cooling System Flow: EGR Coolers

• Cooled coolant flows out of the supply port of the front

cover where it is routed to the horizontal cooler at the left

rear side of the engine.

• The coolant then exits the horizontal cooler and is

immediately routed into the vertical cooler. The coolant

then exits the vertical cooler where it is routed to the return

port in the front cover.

• There is a small port at the top of the vertical cooler where

coolant is allowed to flow to the EGR valve, cool the valve,

then the coolant is routed to the degas bottle. This port is

also used as the deaeration port.

• Coolant flows through the EGR coolers and removes heat

from the exhaust before the exhaust arrives at the EGR

valve.

Coolant Pump & Front Cover

• The coolant pump, (hub and impeller) is mounted into the

front cover which is the housing for the water pump.

• The coolant pump impeller pulls coolant from the center of

the housing and pushes it outward.

• The coolant pump has a built in reservoir to catch small

amounts of coolant that during normal operation of the

engine may seep past the seal. This coolant will evaporate

over time.

Note: The coolant pump impeller may be

damaged if dropped or hit by a hard object.

Injector Sleeve

• The 6.4L Power Stroke uses stainless steel injector sleeves

to seal coolant from the injector and to transfer heat from

the injector to the coolant.

• The injector sleeve is replaceable.

EGR Cooler Horizontal
Coolant Supply

EGR Cooler Vertical
Coolant Supply
from Horizontal
Outlet

EGR Cooler
Vertical
Coolant
Outlet/Return
to Front Cover

EGR Valve Coolant
Supply

Injector Sleeve

Summary of Contents for 6.4L Power Stroke








































































































Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands

Ford 6.4L Power Stroke, Manual

Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands