Ford 6.4L Power Stroke Manual Download Page 8

Page: 8 / 103

6.4L POWER STROKE

DIESEL OvERvIEW

6.4L Power Stroke Diesel Specifications

Engine Type ...........................................................................................Diesel, 4 Cycle

Configuration ................................................................4 OHV/1 Cam-in-Crankcase-V8

Displacement .....................................................................................390 cu. in. (6.4L)

Bore & Stroke ................................................................3.87 X 4.134 (98.2 X 105 mm)

Compression Ratio .............................................................................................17.5:1

Aspiration .................................................................Series Sequential Turbo with CAC

Rated Power @ RPM ..........................................................................350 @ 3000 RPM

Peak Torque @ RPM ...........................................................................650 @ 2000 RPM

Engine Rotation, Facing Flywheel ....................................................Counter Clockwise

Combustion System ...................................High Pressure Common Rail Direct Injection

Total Engine Weight (auto with oil) ................................................1130 lb. (498.95 kg)

Coolant Flow (to radiator)....................................125 gal/min (473 L/min) @ 3000 RPM

Air Flow @ RPM (compressor inlet).......................744 CFM (21.1 m3/min) @ 3000 RPM

Exhaust Flow @ RPM (engine outlet)..................1962 CFM (55.6 m3/min) @ 3000 RPM

Oil Flow @ RPM .....................................................13 gal/min (59 L/min) @ 3000 RPM

Cooling System Capacity (engine only) ..................................................25.3 qts (24 L)

Lube System Capacity (including filter) ................................................15 qts. (14.2 L)

Firing Order ........................................................................................1-2-7-3-4-5-6-8

Specifications

• The cylinders of the 6.4L Power Stroke Diesel are

numbered from the front on the right side 1,3,5,7

and from the front on the left side 2,4,6,8.

Summary of Contents for 6.4L Power Stroke








































































































Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands

Ford 6.4L Power Stroke, Manual

Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands