Ford 6.4L Power Stroke Manual Download

Page: 25 / 103

Lubrication SyStem

Oil Cooler Flow

Oil Filter Base

Oil Cooler Cover

Oil Cooler

Uncooled/Unfiltered Oil

Cooled/Unfiltered Oil

Cooled/Filtered Oil

Filter Drainback Oil

Lube System Flow: Oil Cooler

• Uncooled/Unfiltered oil is directed out of the crankcase at the front

left corner of the engine via a drilled passage from the oil pump.

• Uncooled/Unfiltered oil is then directed across the

oil cooler cover then down into the oil cooler.

• The oil is then cooled via the oil cooler as it passes

through the cooler towards the front of the engine.

• The cooled/unfiltered oil is routed up through the oil cooler cover

then through the oil filter base where it enters the oil filter housing

(there is a small inlet valve in the oil filter base that the oil must

pass through to keep the oil from draining out of the filter housing

during non-operation). At this point the oil flows through the filter

(from the outside of the filter to the center) where it is cleaned.

Note: There is an oil filter bypass valve located at the top of

the oil filter stand pipe (plastic tube the oil filter slides over)

which will open and allow unfiltered oil to enter the system

whenever a pressure differential of 27 psi is reached.

• After being cleaned via the oil filter, the oil is routed through

the oil filter base and into a cavity that has ports to direct

the oil to the follwing areas: left and right oil galleries,

turbocharger oil supply, and the EOT & EOP sensors.

Note: There is a drain valve inside the oil filter base which is held

closed by the oil filter whenever the oil filter cap is tight. Whenever

this cap is loosened, the valve is allowed to open and oil will then

escape through this valve, through the oil cooler cover, and then

down through a drilled passage in the crankcase to the oil pan.

Note: There is an oil cooler bypass valve inside the oil

fllter base which will open and let uncooled oil bypass

the oil cooler and enter the oil filter housing whenever

a pressure differential of 25 psi is reached.

Inlet/Anti-Drainback Valve

Oil Cooler Bypass Valve

Drain Valve

Summary of Contents for 6.4L Power Stroke








































































































Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands

Ford 6.4L Power Stroke, Manual

Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands