Ford 6.4L Power Stroke Manual Download Page 38

Page: 38 / 103

AIR MAnAgeMent SySteM

INTAKE AIRFLOW (Blue)

• Air enters the low pressure turbocharger from the air filter.

• The low pressure turbocharger compresses the air and

sends the air through the extension tube and the crossover

tube prior to entering the high pressure turbocharger.

• The high pressure turbocharger further compresses the air and

sends the air to the charge air cooler (CAC) where the air is cooled

by an air-to-air cooler prior to entering the intake manifold.

EXHAUST AIRFLOW (Red)

• Exhaust gas enters the high pressure turbocharger

turbine housing after being directed through the

exhaust up-pipes at the rear of the engine.

• The high pressure turbocharger turbine contains the

vanes which are controlled by the turbocharger actuator.

These vanes continually change the velocity of the exhaust

gas in the high pressure turbocharger turbine.

• After the exhaust gas has passed through the high

pressure turbocharger turbine it immediately enters

the low pressure turbocharger turbine.

• Once the exhaust gas has powered the low pressure

turbocharger turbine the exhaust gas exits through

the housing towards the rear of the engine where it is

directed to the exhaust aftertreatment system.

Low Pressure
Turbocharger

High Pressure
Turbocharger

Summary of Contents for 6.4L Power Stroke








































































































Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands

Ford 6.4L Power Stroke, Manual

Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands