Ford 6.4L Power Stroke Manual Download

Page: 22 / 103

Lubrication System Features

• Integrated Oil Cooler

• No External Oil Passages in Crankcase

• Easy Access Cartridge Style Oil Filter

• External Oil Pressure Regulator

Lubrication SyStem

Lubrication System Features

• The 6.4L Power Stroke

Diesel uses an oil cooler that is

mounted in the valley of the engine under the oil filter.

• The oil filter is a cartridge style filter mounted

on the top of the engine for ease of service. This

system also incorporates a valve that drains the

oil to the pan when the filter is removed.

• The gerotor oil pump and oil pressure regulator are both

located in the front of the engine behind the vibration

damper in their own removeable aluminum housing.

Summary of Contents for 6.4L Power Stroke








































































































Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands

Ford 6.4L Power Stroke, Manual

Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands