Ford 6.4L Power Stroke Manual Download

Page: 96 / 103

diagnostic codes

DTC

How Set

Code Description

Brief Description

Software Parameters

Required to Set Code

Service Instructions /

Part Replaced

O R C

P0402

Exhaust Gas Recirculation

Flow Excessive Detected

This error occurs when the estimated EGR percent is greater

than the maximum limit for the operating condition.

DPF regeneration not requested
PTO not active
Pressure ratio across EGR valve < 1
rate of change of engine speed < 0.05
rate of change of indicated

torque setpoint < 0.05
600 rpm <engine speed< 800 rpm
45Nm <tqi_sp< 174Nm
12 sec to run test
2 low flow failures required to set

fault (test runs 5 times per trip)
60 sec wait time between tests

EGR system error

P0403

Exhaust Gas Recirculation

Control Circuit

This error occurs when the current through the EGR

control circuit is outside of a predetermined range.

Internal to the engine control module

Wiring, EGR valve

assembly, PCM

P0404

Exhaust Gas Recirculation

Control Circuit Range/

Performance

This error is set when the deviation in EGR

position is outside the threshold.

10 percent of full range error >5 sec

System error, EGR valve, PCM

P0405

Exhaust Gas Recirculation

Sensor A Circuit Low

This error occurs when the EGR position voltage is below the

specified voltage for a predetermined amount of time. This

error can indicate either a short to ground or an open circuit.

0.24v <3 sec

Wiring, EGR valve

assembley, PCM

P0406

Exhaust Gas Recirculation

Sensor A Circuit High

This error occurs when the EGR position voltage is

above the specified voltage, for maximum position given

the current operation, for a predetermined amount of

time. This error can indicate a short to power.

4.84v <3 sec

Wiring, EGR valve

assembley, PCM

P041B

Exhaust Gas Recirculation

Temperature Sensor B

Circuit Range/Performance

This error occurs when the change in the EGR

cooler outlet temperature is less than the threshold

for a predetermined period of time.

Initial ECT < 30 deg C
ECT increase to > 80 deg

C during drive cycle
ECM on time > 3 seconds
TEGR_IN has not changed more

than 6 deg. C in 2 drive cycles

Wiring, Tegr_OUT sensor, PCM

P041C

Exhaust Gas Recirculation

Temperature Sensor

B Circuit Low

This error occurs when the EGR cooler outlet sensor

temperature output value is lower than a minimum

probable temperature for a predetermined amount of

time, indicating an open circuit or short to power.

0.15v > 5sec.

Wiring, Tegr_OUT sensor, PCM

P041D

Exhaust Gas Recirculation

Temperature Sensor

B Circuit High

This error occurs when the EGR cooler outlet

sensor temperature output value is higher than a

maximum probable temperature for a predetermined

period of time, indicating a short to ground.

N > 650 rpm
torque setpoint >53 N-m
ECT > 60 deg C
4.95v > 5 sec

Wiring, Tegr_OUT sensor, PCM

P0420

REGEN

Catalyst System Efficiency

Below Threshold

This error occurs if the observed exothermic reaction (a

reaction that produces heat) during a regeneration event

falls below a threshold for a predetermined period of time.

P042E

EGR Control Stuck Open

This error occurs when the EGR set point is less

than a specified threshold, the actual EGR position

is greater than a specified threshold, and the EGR

control limit is less than a specified limit.

EGR Position > 30 %
EGR Position desired < 15% > 4 sec

System error, EGR valve, PCM

P042F

EGR Control Stuck Closed

This error occurs when the EGR set point is greater

than a specified threshold, the actual EGR position

is less than a specified threshold, and the EGR

control limit is greater than a specified limit.

EGR Position < 15 %
EGR Position desired > 30% > 4 sec

System error, EGR valve, PCM

P0472

Exhaust Pressure Sensor

A Circuit Low

This error occurs when the EP signal voltage is lower than

a specified value for a predetermined period of time.

0.15v < 3 sec

Wiring, EP sensor, PCM

P0473

Exhaust Pressure Sensor

A Circuit High

This error occurs when the EP signal voltage is higher than

a specified value for a predetermined amount of time.

4.90v < 3 sec

Wiring, EP sensor, PCM

P0480

Fan 1 Control Circuit

P0488

EGR Throttle Position Control

Range/Performance

This error occurs when there is an error in throttle position

vs. desired position, high temperature condition and throttle

not returned to open position when commanded, faulty

input signal detected, or broken return spring detected.

THR_STATE is low > 3 sec

Wiring, EGRTP, PCM

P0494

Fan Speed Low

P0495

Fan Speed High

P0500

Vehicle Speed Sensor A

This error occurs when either a faulty signal or a missing

signal occurs from the vehicle speed sensor circuit.

P0503

Vehicle Speed Sensor A

Intermittent/Erratic/High

This error occurs when an intermittent error is

detected in the vehicl speed sensor circuit.

Summary of Contents for 6.4L Power Stroke








































































































Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands

Ford 6.4L Power Stroke, Manual

Search results

Summary of Contents for 6.4L Power Stroke

Reviews:

Related manuals for 6.4L Power Stroke

Brands by name

Popular brands