manualshive.com logo in svg

Ford 2011 Taurus, Owner'S Manual

The Ford 2011 Taurus Owner's Manual is a comprehensive guide that provides essential information on operating, maintaining, and troubleshooting your vehicle. Available for free download at manualshive.com, this manual offers clear instructions, diagrams, and tips to ensure a smooth and enjoyable driving experience.

Share
Download
background image

Safety belt height adjustment

Your vehicle has safety belt height
adjustments for the front outboard
seating positions.

Adjust the height of the shoulder
belt so the belt rests across the
middle of your shoulder.

To adjust the shoulder belt height,
squeeze the button and slide the
height adjuster up or down. Release
the button and pull down on the
height adjuster to make sure it is locked in place.

WARNING:

Position the safety belt height adjusters so that the

belt rests across the middle of your shoulder. Failure to adjust

the safety belt properly could reduce the effectiveness of the seat belt
and increase the risk of injury in a collision.

Safety belt warning light and indicator chime

The safety belt warning light illuminates in the instrument cluster and a
chime sounds to remind the occupants to fasten their safety belts.

Conditions of operation

If...

Then...

The driver’s safety belt is not
buckled before the ignition is
on...

The safety belt warning light
illuminates 1-2 minutes and the
warning chime sounds 4-8 seconds.

The driver’s safety belt is
buckled while the indicator
light is illuminated and the
warning chime is sounding...

The safety belt warning light and
warning chime turn off.

The driver’s safety belt is
buckled before the ignition is
on ...

The safety belt warning light and
indicator chime remain off.

Seating and Safety Restraints

166

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Ecco EW4010 Installation And Operation Instructions Manual preview
EW4010
Brand: Ecco Pages: 9
Ecco EW4009 Installation And Operation Instructions Manual preview
EW4009
Brand: Ecco Pages: 9
TATA Motors Indigo Owner'S Manual & Service Book preview
Indigo
Brand: TATA Motors Pages: 164
Vauxhall Ampera Owner'S Manual preview
Ampera
Brand: Vauxhall Pages: 199
Globalsat MR-350P Installation Manual preview
MR-350P
Brand: Globalsat Pages: 2
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Brand: Valeo Pages: 25
Thule PORTAGE 819 Instructions Manual preview
PORTAGE 819
Brand: Thule Pages: 12
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Brand: Alphasonik Pages: 8
Renault Laguna III Manual preview
Laguna III
Brand: Renault Pages: 3699
Revelation lnd-10716 Installation Instructions preview
lnd-10716
Brand: Revelation Pages: 4
Discount Car Stereo A2DIY-JAG98 Quick Start Manual preview
A2DIY-JAG98
Brand: Discount Car Stereo Pages: 11
AUTOTECH 10.109.405K Installation Instructions preview
10.109.405K
Brand: AUTOTECH Pages: 2
WABCO 2S/2M Installation Instructions Manual preview
2S/2M
Brand: WABCO Pages: 40
ABB InCharge Terra AL2-40-240-T1-WC1R Installation Manual preview
InCharge Terra AL2-40-240-T1-WC1R
Brand: ABB Pages: 39
NAV TOOL NAVTOOL6.0-AR2-HDMI Installation Manual preview
NAVTOOL6.0-AR2-HDMI
Brand: NAV TOOL Pages: 19
Crux SWRGM-49 Manual preview
SWRGM-49
Brand: Crux Pages: 5
Metra Electronics 108-TO1 Series Installation Instructions Manual preview
108-TO1 Series
Brand: Metra Electronics Pages: 16
Crux BEECR-35P Manual preview
BEECR-35P
Brand: Crux Pages: 2

Brands by name

Popular brands

Load more brands