Ford 2011 Taurus Page 234 Owner'S Manual Download | Manualshive

Page: 234 / 408

background image

The braking system of the tow vehicle is rated for operation at the
GVWR not GCWR.

Trailer lamps

Trailer lamps are required on most towed vehicles. Make sure all running
lights, brake lights, turn signals and hazard lights are working. Do not
connect trailer lamps directly to your vehicle’s tail lamps. This can cause
damage to your vehicle’s electrical system. Contact your authorized
dealer or trailer rental agency for proper instructions and equipment for
hooking-up trailer lamps.

WARNING:

Never connect any trailer lighting to the vehicle’s

tail lamp circuits, because it may damage the electrical system

resulting in fire. Contact your authorized dealer as soon as possible for
assistance in proper trailer tow wiring installation. Additional electrical
equipment may be required.

Driving while you tow

When towing a trailer:

•

Turn off the speed control. The speed control may shut off
automatically when you are towing on long, steep grades.

•

It is recommended to select the L (Low) or M (Manual) gear position
when additional engine braking is needed. In situations such as
prolonged downhill driving on steep grades (i.e., driving in
mountainous areas), additional engine braking is needed to reduce the
load on the vehicle’s regular brake system to prevent them from
overheating.

•

Allow more distance for stopping with a trailer attached; anticipate
stops and brake gradually.

Trailer towing tips

•

Practice turning, stopping and backing-up before starting on a trip to
get the feel of the vehicle-trailer combination. When turning, make
wider turns so the trailer wheels will clear curbs and other obstacles.

•

To aid in engine/transmission cooling and A/C efficiency during hot
weather while stopped in traffic, place the gearshift lever in P (Park).

•

After you have traveled 50 miles (80 km), thoroughly check your
hitch, electrical connections and trailer wheel lug nuts.

•

If you are driving down a long or steep hill, shift to a lower gear. Do
not apply the brakes continuously, as they may overheat and become
less effective.

Tires, Wheels and Loading

234

2011 Taurus
Owners Guide, 3rd Printing
USA

(fus)

«
...
232
233
234
235
236
...
»

Summary of Contents for 2011 Taurus

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Taurus

Brand: RACLET Pages: 48

Brand: RACLET Pages: 31

Brand: Porsche Pages: 51

Brand: Whispbar Pages: 14

Brand: Ford Pages: 38

2010 Civic Sedan

Brand: Honda Pages: 390

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

Brand: Volvo Pages: 211

Brand: Honda Pages: 253

Brand: Toyota Pages: 11

iTrip Bluetooth

Brand: Griffin Technology Pages: 6

Pajero Pinin 1999

Brand: Mitsubishi Pages: 919

Brand: Brainz Pages: 2

Brand: Reese Pages: 21

Brand: Van Guard Pages: 3

DELTA HF integrale

Brand: Lancia Pages: 101

Brand: Mahindra Pages: 247

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands